- 您现在的位置：买卖IC网 > PDF目录16316 > AS1916S-T (ams)IC SUPERVISOR ACT LOW SOT23-5 PDF资料下载
参数资料
| 型号： | AS1916S-T |
| 厂商： | ams |
| 文件页数： | 9/15页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR ACT LOW SOT23-5 |
| 标准包装： | 1 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.93V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | AS1916S-TDKR |
AS1916 - AS1918
Datasheet - D e t a i l e d D e s c r i p t i o n
8.2 Watchdog Input
The integrated watchdog feature can be used to monitor processor activity via pin WDI, and can detect pulses as short as 50ns. The watchdog
requires that the processor toggle the watchdog logic input at regular intervals, within a specified minimum timeout period (1.5s, typ). A reset is
asserted for the reset timeout period. As long as reset is asserted, the timer remains cleared and is not incremented. When reset is deasserted,
the watchdog timer starts counting ( Figure 11 ).
Note: The watchdog timer can be cleared with a reset pulse or by toggling WDI.
Figure 11. Watchdog Timing Relationship
VCC
t RST
RESETN
t RP
t WD
t RP
WDI
The RESET signal is the inverse of the RESETN signal.
The watchdog is internally driven low during most (87.5%) of the watchdog timeout period (see t WD on page 5 ) and high for the rest of the
watchdog timeout period. When pin WDI is left unconnected, this internal driver clears the watchdog timer every 1.4s. When WDI is tri-stated or
is not connected, the maximum allowable leakage current is 10μA and the maximum allowable load capacitance is 200pF.
Note: The watchdog function can be disabled by leaving pin WDI unconnected or connecting it to a tri-state output buffer.
8.3 Manual Reset Input
The active-low pin MRN is used to force a manual reset. This input can be driven by CMOS logic levels or with open-drain collector outputs.
Pulling MRN low asserts a reset which will remain asserted as long as MRN is kept low, and for the timeout period (see t RP on page 4 ) after
MRN goes high (140ms min). The manual reset circuitry has an internal 50k Ω pullup resistor, thus it can be left open if not used.
To create a manual-reset circuit, connect a normally open momentary switch from pin MRN to GND (see Figure 1 on page 1) ; external debounce
circuitry is not required in this configuration.
If MRN is driven via long cables or the device is used in a noisy environment, a 0.1μF capacitor between pin MRN and GND will provide
additional noise immunity.
www.austriamicrosystems.com/Supervisors/AS1916
Revision 1.04
8 - 14
相关PDF资料 |
PDF描述 |
|---|---|
| 2-6278899-5 | CA,62.5,MTRJ-ST |
| VE-J1R-EZ-F2 | CONVERTER MINIMOD DC/DC 7.5V 25W |
| 2-6278898-5 | C/A 62.5/125UM,ZIPST,MTRJ 20M |
| ADM1066ASUZ | IC SUPERVISOR/SEQUENCER 48-TQFP |
| ECO-S2GA181EA | CAP ALUM 180UF 400V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS1916V-T | 功能描述:IC SUPERVISOR ACT LOW SOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| AS1916Z-T | 功能描述:IC SUPERVISOR ACT HIGH SOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| AS1917 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:Microprocessor Supervisory Circuits with Manual Reset and Watchdog |
| AS191-73 | 制造商:ALPHA 制造商全称:ALPHA 功能描述:PHEMT GaAs IC High Linearity 3 V Control SPDT Switch 0.1-2 GHz |
| AS191-73LF | 功能描述:RF 开关 IC .1-4.0GHz SPDT GaAs IL .5dB RoHS:否 制造商:M/A-COM Technology Solutions 开关数量:Single 开关配置:SPDT 介入损耗:0.6 dB 截止隔离（典型值）:43 dB 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:PQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。