- 您现在的位置：买卖IC网 > PDF目录255368 > AS2320-7PB1 (POWER-ONE INC) 2-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | AS2320-7PB1 |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封装： | METAL, CASE S02, MODULE |
| 文件页数： | 4/33页 |
| 文件大小： | 438K |
| 代理商： | AS2320-7PB1 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 12 of 33
www.power-one.com
Fig. 15
Typical output response as a function of inhibit control
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Vinh Inhibit Vo = on Vi min - Vi max –50
0.8
V
voltage
Vo = off
2.4
50
Iinh Inhibit current
Vinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
1
Vo/Vo nom
tr
tf
06001
Sense Lines
(Only single output models)
Important: Sense lines must always be connected! Incorrectly
connected sense lines may activate the overvoltage limitation,
resulting in a permanent short-circuit of the output.
This feature allows for compensation of voltage drops across the
connector contacts and if necessary, across the load lines. If the
sense lines are connected at the load rather than directly at the
connector, the user should ensure that the voltage differences
specified in the table below are not exceeded. We recommend
connecting the sense lines directly at the female connector.
To ensure correct operation, both sense lines (S+ and S–) should
be connected to their respective power outputs (Vo1+ and Vo1–)
and the voltage difference between any sense line and its
respective power output pin (as measured on the connector)
should not exceed the following values:
Table 6: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12, 15, 24 V
< 1.0 V
< 0.25 V
If the output voltages are increased above Vo nom via the R-input
control, option P setting, remote sensing or option T, the output
currents must be reduced accordingly so that Po nom is not
exceeded.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input the output is disabled.
The outputs may be enabled or disabled by means of a logic
signal (TTL, CMOS, etc.) applied between the inhibit input i and
the negative pin of output 1 (Vo1–). In systems with several
converters, this feature can be used to control the activation
sequence of the converters. If the inhibit function is not required,
connect the inhibit pin 18 to pin 14 to enable the outputs (active
low logic, fail safe).
Vi+
Vi–
Vo–
i
Vo+
Iinh
Vinh
06031
1.6
0.8
0
–0.8
–50
Vinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Vinh = 0.8 V
Vo = on
Vo = off
Vinh = 2.4 V
06032
Fig. 13
Definition of Vinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Vinh
相关PDF资料 |
PDF描述 |
|---|---|
| AS2320-7RT | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| AS2320-9RD9T | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| AS2320-9RDDTB1 | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| AS2540-9PD0B1 | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| AS2540-9RD1T | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS2320-7R | 功能描述:EURO-CASSETTE 100W 2X 12V RoHS:否 类别:电源 - 外部/内部（非板载） >> DC DC Converters 系列:* 标准包装:1 系列:Quint 类型:隔离 输入电压:24V 输出:24V 输出数:1 输出 - 1 @ 电流（最大）:24 VDC @ 50A 输出 - 2 @ 电流（最大）:- 输出 - 3 @ 电流（最大）:- 输出 - 4 @ 电流（最大）:- 功率（瓦特）:1200W 安装类型:底座安装 工作温度:0°C ~ 40°C 效率:- 封装/外壳:模块 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包装:散装 电源（瓦特）- 最大:1200W 批准:- 其它名称:277-69722866365-NDQUINT-BAT/24DC/12AH |
| AS2320-9R | 制造商:Power-One 功能描述:DCDC - Bulk |
| AS23240FLF | 制造商:TT Electronics / IRC 功能描述:AS23240FLF |
| AS23240HLF | 制造商:TT Electronics / IRC 功能描述:AS23240HLF |
| AS23240JLF | 制造商:TT Electronics / IRC 功能描述:AS23240JLF |
发布紧急采购，3分钟左右您将得到回复。