- 您现在的位置：买卖IC网 > Datasheet目录395 > AS3931-ZTSU (ams)IC ASK RECEIVER LF 3CH 16-TSSOP Datasheet资料下载
参数资料
| 型号： | AS3931-ZTSU |
| 厂商： | ams |
| 文件页数： | 22/31页 |
| 文件大小： | 0K |
| 描述： | IC ASK RECEIVER LF 3CH 16-TSSOP |
| 标准包装： | 96 |
| RF 型： | 接收器 |
| 频率： | 19kHz ~ 150kHz |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
AS3931
Datasheet - C o n f i g u r i n g t h e P r o d u c t
9.3.4
C5 (WAKE Clear)
Bit C5 is used to reset the active low WAKE pin after the pin has been set as a result of receiving a valid code word (single or double wake
pattern) by one of the 3 channels, a POR or an internally generated Wakeup. Setting Bit C5 to 1, the WAKE pin is reset to high and held in high
state, to enable the channels for the next wake up signal, the bit C5 must be toggled to 0 afterwards. After power on, the WAKE-pin is activated
and the bit C5 has to be toggled high and low after a power on.
Table 15. C5 Bit Mode
9.4 Test Mode Register
Table 16. Register Data
C5
0
1
Mode
no effect
WAKE=H
Bit
T0
T1
T2
T3
T4
T5
Table 17. Register Address
Bit
A0
A1
POR state
0
0
0
0
1
0
Description
Test mode enable
Test mode select Bit 1
Test mode select Bit 2
not used
RSSI step
WAKE Generator on/off
Value
0
1
9.4.1
T0 (Test Mode Enable)
Bit T0 is used to define the pin function of the WAKE pin. When bit T0 is reset to 0, the WAKE pin is used for normal Wake Up detection (Single
or Double Wakeup from the receiver channels or internally generated wakeup). When bit T0 is set to 1, testmode signals are multiplexed to the
WAKE pin according to the selected test mode (T1, T2). After power on, the normal wake up detection mode is selected.
Table 18. T0 Bit Mode
T0
0
1
WAKE Pin function
WAKE
Test Mode Signals
9.4.2
T1, T2 (Test Mode Select)
When bit T0 is set to 1, the following signals can be mapped to the WAKE pin. For signal description (see Figure 13) .
DATA: received bit stream of the selected channel
WAKE: detected wake up of the selected channel
For the DATA and WAKE signal select the desired channel by setting Bits C0 and C1.
Table 19. T1, T2 Bit Mode
T1
0
1
www.austriamicrosystems.com/AS3931
T2
0
0
Revision 6.2
WAKE Pin Function
DATA of selected channel
WAKE of selected channel
21 - 30
相关PDF资料 |
PDF描述 |
|---|---|
| AS3932-BTST | IC RF PROGRAM 16-TSSOP |
| AS500106 | TLAPS MAGNET CARRIER |
| AS5263-HQFT-500 | IC ENCODER ROTARY 12BIT 32-QFN |
| AT 150 B420L | SENSOR CURRENT 150A 30V MOD |
| AT 150 B5 | SENSOR CURRENT 150A MOD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS3932 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:3D Low Frequency Wakeup Receiver |
| AS3932 DB | 功能描述:BOARD DEMO AS3932 RX/TX RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| AS3932 DEMOBOARD | 功能描述:BOARD DEMO AS3932 RX/TX 制造商:ams 系列:- 零件状态:有效 类型:接收器 频率:125kHz 配套使用产品/相关产品:AS3932 所含物品:板 标准包装:1 |
| AS3932 DK | 功能描述:BOARD SYSTEM AS3932 RX/TX RoHS:否 类别:RF/IF 和 RFID >> RF 评估和开发套件，板 系列:- 标准包装:1 系列:- 类型:GPS 接收器 频率:1575MHz 适用于相关产品:- 已供物品:模块 其它名称:SER3796 |
| AS3932-BQFT | 功能描述:射频接收器 RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。