- 您现在的位置：买卖IC网 > PDF目录17280 > AS5030 AB (ams)BOARD ADAPTER AS5030 PDF资料下载
参数资料
| 型号： | AS5030 AB |
| 厂商： | ams |
| 文件页数： | 23/44页 |
| 文件大小： | 0K |
| 描述： | BOARD ADAPTER AS5030 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | 串行 |
| 电源电压： | 5V |
| 嵌入式： | 否 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS5030 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AS5030
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.1 AS5030 Programming
The AS5030 has an integrated 18-Bit OTP ROM for configuration purposes.
8.1.1
OTP Programming Options
The OTP programming options can be set permanently by programming or temporarily by overwriting. Both methods are carried out over the
serial interface, but with different commands (WRITE OTP, PROG OTP).
Note: During the 18bit OTP programming, each bit needs 4 clock pulses to be validated.
?? Zero Position
Programming
This programming option allows the user to program any rotation angle of the magnet as the new zero position. This useful feature simpli-
fies the assembly process as the magnet does not need to be mechanically adjusted to the electrical zero position. It can be assembled in
any rotation angle and later matched to the mechanical zero position by zero position programming.
The 8-bit user programmable zero position can be applied both temporarily (command WRITE OTP, #1F H ) or permanently (command
PROG OTP, #19 H )
?? Magnetic Field Optimization
This programming option allows the user to match the vertical distance of the magnet with the optimum magnetic field range of the AS5030
by setting the sensitivity level.
The 2-bit user programmable sensitivity setting can be applied both temporarily (command WRITE OTP, #1F H ) or permanently (command
PROG OTP, #19 H )
8.1.2
Reduced Power Mode Programming Options
These temporary programming options are also carried out over the serial interface.
?? Low Power Mode
Low Power Mode is a power saving mode with fast start-up. In Low Power Mode, all internal digital registers are frozen and the power con-
sumption is reduced to max. 1.5mA. The serial interface remains active. Start-up from this mode to normal operation can be accomplished
within 150μs. This mode is recommended for applications, where low power, but fast start-up and short reading cycle intervals are required.
?? Ultra-low Power Mode
Ultra-low Power Mode is a power saving mode with even reduced power-down current consumption. In this mode, all chip functions are fro-
zen and the power consumption is reduced to max. 50μA. The serial interface remains active. Start-up from this mode to normal operation
can be accomplished within 500μs. This mode is recommended for applications, where very low average power consumption is required,
e.g. for battery operated equipment. For example, in a cycled operation with 10 readings per second, the average power consumption of the
AS5030 can be reduced to only 120μA.
8.2 AS5030 Read / Write Commands
Data transmission with the AS5030 is handled over the 2-wire or 3-wire interface. The transmission protocol begins with sending a 5-bit
command to the AS5030, followed by reading or writing 16 or 18 bits of data:
8.2.1
16-bit Read Command
Command
Bin
Hex
D15
D14
D13 D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
RD
ANGLE
00000
00
C2
lock
AGC 5:0
Angle 7:0
C2 displays status of hardware pin C2 (pin #15)
Lock indicates that the AGC is locked. Data is invalid when this bit is 0
AGC 6-bit AGC register. Indicates the strength of the magnet (e.g. for push-button applications)
000000 b indicates a strong magnetic field
111111 b indicates a weak magnetic field
ideally, the vertical distance of the magnet should be chosen such that the AGC value is in the middle (around 100000b)
Angle 8-bit Angle value; represents the rotation angle of the magnet. One step = 360°/256 = 1.4°
www.ams.com/AS5030
Revision 2.4
23 - 44
相关PDF资料 |
PDF描述 |
|---|---|
| EEV-HB1E330P | CAP ALUM 33UF 25V 20% SMD |
| 195D226X9015G2T | CAP TANT 22UF 15V 10% 2810 |
| 0210490748 | CABLE JUMPER 1.25MM .076M 7POS |
| ASPI-0403S-151M-T | INDUCTOR POWER 150UH 20% SMD |
| MAX15015AEVKIT+ | EVAL KIT FOR MAX15015A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5030ATST | 制造商:ams 功能描述:T&R / TSSOP 16 |
| AS5030-ATST | 功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| AS5030ATSU | 制造商:AMS 功能描述:IC MAGNETIC ROTARY ENCODER 8BIT 16-TSSO 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 8BIT 16-TSSO 制造商:AMS 功能描述:IC, MAGNETIC ROTARY ENCODER 8BIT 16-TSSOP; IC Function:Encoder IC; Brief Features:360 Contactless Angular Position Encoding, Two Digital 8-bit Absolute Output; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; No. of Pins:16 ;RoHS Compliant: Yes |
| AS5030-ATSU | 功能描述:板机接口霍耳效应/磁性传感器 RoHS:否 制造商:Honeywell 类型:Bipolar Hall-Effect Digital Position Sensor 工作电源电压:3 V to 24 V 电源电流:3.5 mA 最大输出电流:20 mA 工作点最小值/最大值:5 G, 55 G 最小/最大释放点（Brp）:- 55 G, - 5 G 最大工作温度:+ 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23 |
| AS5030-DB | 功能描述:磁传感器开发工具 AS5030 Demo Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
发布紧急采购，3分钟左右您将得到回复。