- 您现在的位置：买卖IC网 > Datasheet目录311 > AS5040 PB (ams)BOARD PROGRAM AS5040 Datasheet资料下载
参数资料
| 型号： | AS5040 PB |
| 厂商： | ams |
| 文件页数： | 26/34页 |
| 文件大小： | 0K |
| 描述： | BOARD PROGRAM AS5040 |
| 特色产品： | AS5140 – Automotive Rotary Encoder IC AS5145 – Automotive Rotary Encoder IC |
| 标准包装： | 1 |
| 模块/板类型： | ZIF 插口 |
| 适用于相关产品： | AS5000 编程器，AS5040 |
| 相关产品： | AS5040-ASSTDKR-ND - IC ENCODER PROG 10-BIT 16-SSOP AS5040-ASSTCT-ND - IC ENCODER PROG 10-BIT 16-SSOP AS5040-ASSTTR-ND - IC ENCODER PROG 10-BIT 16-SSOP |
| 其它名称： | AS5045 PB AS5140H PB AS5145 PB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5040
Data Sheet
The angular displacement ( Θ ) of the magnetic source with reference to the Hall sensor array may then be modelled
( Y 1 ? Y 2 ) ± 0 . 5 °
by:
Θ = arctan
( X 1 ? X 2 )
The ± 0.5° angular error assumes a magnet optimally aligned over the center of the die and is a result of gain
mismatch errors of the AS5040. Placement tolerances of the die within the package are ± 0.235mm in X and Y
direction, using a reference point of the edge of pin #1 (Figure 23).
In order to neglect the influence of external disturbing magnetic fields, a robust differential sampling and ratiometric
calculation algorithm has been implemented. The differential sampling of the sine and cosine vectors removes any
common mode error due to DC components introduced by the magnetic source itself or external disturbing magnetic
fields. A ratiometric division of the sine and cosine vectors removes the need for an accurate absolute magnitude of
the magnetic field and thus accurate Z-axis alignment of the magnetic source.
The recommended differential input range of the magnetic field strength (B (X1-X2) ,B (Y1-Y2) ) is ± 75mT at the surface of
the die. In addition to this range, an additional offset of ± 5mT, caused by unwanted external stray fields is allowed.
The chip will continue to operate, but with degraded output linearity, if the signal field strength is outside the
recommended range. Too strong magnetic fields will introduce errors due to saturation effects in the internal
preamplifiers. Too weak magnetic fields will introduce errors due to noise becoming more dominant.
17 Failure Diagnostics
The AS5040 also offers several diagnostic and failure detection features:
Magnetic Field Strength Diagnosis
By software: the MagINCn and MagDECn status bits will both be high when the magnetic field is out of range.
By hardware: Pins #1 (MagINCn) and #2 (MagDECn) are open-drain outputs and will both be turned on (= low with
external pull-up resistor) when the magnetic field is out of range. If only one of the outputs is low, the magnet is either
moving towards the chip (MagINCn) or away from the chip (MagDECn).
Power Supply Failure Detection
By software: If the power supply to the AS5040 is interrupted, the digital data read by the SSI will be all “0”s. Data is
only valid, when bit OCF is high, hence a data stream with all “0”s is invalid. To ensure adequate low levels in the
failure case, a pull-down resistor (~10k Ω ) should be added between pin DO and VSS at the receiving side.
By hardware: The MagINCn and MagDECn pins are open drain outputs and require external pull-up resistors. In
normal operation, these pins are high ohmic and the outputs are high (see Table 3). In a failure case, either when the
magnetic field is out of range or the power supply is missing, these outputs will become low. To ensure adequate low
levels in case of a broken power supply to the AS5040, the pull-up resistors (>10k Ω ) from each pin must be
connected to the positive supply at pin 16 (VDD5V).
By hardware: PWM output: The PWM output is a constant stream of pulses with 1kHz repetition frequency. In case of
power loss, these pulses are missing.
By hardware: Incremental outputs: In normal operation, pins A(#3), B(#4) and Index (#6) will never be high at the
same time, as Index is only high when A=B=low. However, after a power-on-reset, if VDD is powered up or restarts
after a power supply interruption, all three outputs will remain in high state until pin CSn is pulled low. If CSn is
already tied to VSS during power-up, the incremental outputs will all be high until the internal offset compensation is
finished (within t PwrUp ).
www.austriamicrosystems.com
Revision 2.10
25 - 33
相关PDF资料 |
PDF描述 |
|---|---|
| AS5043 PB | BOARD PROGRAM AS5043 |
| AS5045 PB | BOARD PROGRAM AS5045 |
| AS5134 PB | BOARD PROGRAM AS5134 |
| AS5140 PB | BOARD PROGRAM AS5140 |
| ASDMB-ADAPTER-KIT | ASDMB MEMSPEED P II OSC KIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5040-SS_EK_AB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_DB | 功能描述:AS5040 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5040 标准包装:1 |
| AS5040-SS_EK_PB | 功能描述:AS5000 Programmer, AS5040 - ZIF Socket 制造商:ams 系列:- 零件状态:有效 模块/板类型:ZIF 插口 配套使用产品/相关产品:AS5000 编程器，AS5040 标准包装:1 |
| AS-5041 | 制造商:Bud Industries Inc 功能描述: |
| AS-5042-A | 功能描述:机架和机柜配件 20" SLIDE SET 3PC RoHS:否 制造商:Bivar 产品:Rack Accessories 面板空间: 颜色:Black |
发布紧急采购，3分钟左右您将得到回复。