- 您现在的位置：买卖IC网 > PDF目录21928 > AS5043-ASSU (ams)IC ENCODER PROG 10-BIT 16-SSOP PDF资料下载
参数资料
| 型号： | AS5043-ASSU |
| 厂商： | ams |
| 文件页数： | 11/37页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER PROG 10-BIT 16-SSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 标准包装： | 77 |
| 传感范围： | 45mT ~ 75mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 3 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 电流 - 电源： | 21mA |
| 电流 - 输出（最大）： | 4mA |
| 输出类型： | 模拟，数字 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AS5043
Data Sheet – Analog Output
11 Analog Output
The analog output V out provides an analog voltage that is proportional to the angle of the rotating magnet and ratiometric
to the supply voltage VDD5V (max.5.5V). It can source or sink currents up to ± 1mA in normal operation (up to 66mA short
circuit current).
The analog output block consists of a digital angular range selector, a 10-bit Digital-to-Analog converter and an OPAMP
buffer stage (see Figure 14).
The digital range selector allows a preselection of the angular range for 360°,180°,90° or 45° (see Table 5). Fine-tuning of
the angular range can be accomplished by adjusting the gain of the OPAMP buffer stage.
The reference voltage for the Digital-to-Analog converter (DAC) can be taken internally from VDD5V / 2. In this mode, the
output voltage is ratiometric to the supply voltage.
Alternatively, an external DAC reference can be applied at pin DACref (#9). In this mode, the analog output is ratiometric
to the external reference voltage.
An on-chip diagnostic feature turns the analog output off in case of an error (broken supply or magnetic field out of range;
see Table 3).
The DAC output can be accessed directly at pin #10 DACout.
The addition of an OPAMP to the DAC output allows a variety of user configurable options, such as variable output
voltage ranges and variable output voltage versus angle response. By adding an external transistor, the analog voltage
output can be buffered to allow output currents up to hundred milliamperes or more.
Furthermore, the OPAMP can be configured as constant current source.
As an OTP option, the DAC can be configured to 2 different output ranges:
a) 0……100% V DACref . The reference point may be either taken from VDD5V/2 or from the external DACref input. The
0…100% range allows easy replacement of potentiometers. Due to the nature of rail-to-rail outputs, the linearity will
degrade at output voltages that are close to the supply rails.
b) 10…..90% V DACref . This range allows better linearity, as the OPAMP is not driven to the rails. Furthermore, this mode
allows failure detection, when the analog output voltage is outside of the normal operating range of 10…90%VDD, as in
the case of broken supply or when the magnetic field is out of range and the analog output is turned off.
11.1 Analog Output Voltage Modes
The Analog output voltage modes are programmable by OTP. Depending on the application, the analog output can be
selected as rail-to-rail output or as clamped output with 10%-90% VDD5V.
The output is ratiometric to the supply voltage (VDD5V), which can range from 3.0V to 5.5V. If the DAC reference is
switched to an external reference (pin DACref), the output is ratiometric to the external reference.
11.1.1 Full Scale Mode
This output mode provides a ratiometric DAC output of (0% to 100%)x Vref *) , amplified by the OPAMP stage (default =
internal 2x gain, see Figure 14)
Figure 8: Analog Output, Full Scale Mode (shown for 360°mode)
Vref
100%
analog
output
voltage
Note: For simplification, Figure 8 describes
a linear output voltage from rail to rail (0V to
VDD). In practice, this is not feasible due to
saturation effects of the OPAMP output
driver transistors. The actual curve will be
rounded towards the supply rails (as
indicated in Figure 8)
0V
0°
90°
180°
270°
angle
360°
Note: Figure 8 and are shown for 360°
operation. See Table 5 (page 16) for further
angular range programming options.
www.austriamicrosystems.com
Revision 1.80
10 – 36
相关PDF资料 |
PDF描述 |
|---|---|
| NFL21SP207X1C3D | FILTER LC HIGH FREQ 22PF 0805 |
| AS5145A-HSST-500 | IC ENCODER ROTARY MAGN 16-SSOP |
| D2JW-01K11L | IMMERSION-PROOF BASIC SWITCH |
| NFL21SP157X1C3D | FILTER LC HIGH FREQ 28PF 0805 |
| AS5030-ATSU | IC ENCODER ROTARY 8-BIT 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5043TR | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:PROGRAMMABLE 360° MAGNETIC ANGLE ENCODER WITH ABSOLUTE SSI AND ANALOG OUTPUTS |
| AS5045 | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12 BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER |
| AS5045 AB | 功能描述:BOARD ADAPTER AS5045 RoHS:否 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| AS5045 DB | 制造商:ams 功能描述:Demoboard for AS5045 Rotary Encoder, Bulk |
| AS5045 DB V2 | 功能描述:BOARD DEMO AS5045 RoHS:否 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
发布紧急采购，3分钟左右您将得到回复。