- 您现在的位置：买卖IC网 > Datasheet目录311 > AS5045 PB (ams)BOARD PROGRAM AS5045 Datasheet资料下载
参数资料
| 型号： | AS5045 PB |
| 厂商： | ams |
| 文件页数： | 22/34页 |
| 文件大小： | 0K |
| 描述： | BOARD PROGRAM AS5045 |
| 标准包装： | 1 |
| 模块/板类型： | ZIF 插口 |
| 适用于相关产品： | AS5000 编程器，AS5045 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
AS5045
Data Sheet
Figure 13. OTP Register Analog Read
ProgEN
OutpEN
Analog Readback Data at PROG
Power-on-
Reset;
CSn
V ref
V programmed
turn off
supply
PWM
PROG
Internal
test bit
digital
Mag
halfEN Comp
EN
PWM
Dis
Z0 V unprogrammed
Z7
Z8
Z9
Z10 Z11 CCW
Prog changes to Output
CLK
t LoadProg
1
CLK Aread
16
12 Alignment Mode
The alignment mode simplifies centering the magnet over the center of the chip to gain maximum accuracy.
Alignment mode can be enabled with the falling edge of CSn while Prog = logic high ( Figure 14 ). The Data bits
D11-D0 of the SSI change to a 12-bit displacement amplitude output. A high value indicates large X or Y
displacement, but also higher absolute magnetic field strength. The magnet is properly aligned, when the difference
between highest and lowest value over one full turn is at a minimum.
Under normal conditions, a properly aligned magnet will result in a reading of less than 128 over a full turn.
The MagINCn and MagDECn indicators will be = 1 when the alignment mode reading is < 128. At the same time,
both hardware pins MagINCn (#1) and MagDECn (#2) will be pulled to VSS. A properly aligned magnet will therefore
produce a MagINCn = MagDECn = 1 signal throughout a full 360° turn of the magnet.
Stronger magnets or short gaps between magnet and IC may show values larger than 128. These magnets are still
properly aligned as long as the difference between highest and lowest value over one full turn is at a minimum.
The alignment mode can be reset to normal operation by a power-on-reset (disconnect / re-connect power supply) or
by a falling edge on CSn with Prog = low.
Figure 14. Enabling the Alignment Mode
Prog
Figure 15. Exiting Alignment Mode
CSn
AlignMode enable
Read-out
via SSI
Prog
CSn
exit AlignMode
Read-out
via SSI
2μs 2μs
min. min.
www.austriamicrosystems.com
Revision 1.7
21 – 33
相关PDF资料 |
PDF描述 |
|---|---|
| AS5134 PB | BOARD PROGRAM AS5134 |
| AS5140 PB | BOARD PROGRAM AS5140 |
| ASDMB-ADAPTER-KIT | ASDMB MEMSPEED P II OSC KIT |
| ASFLMPLP-ADAPTER-KIT | ASFLMPLP MEMSPEED P II OSC KIT |
| AT24C01-10SI-1.8 | IC EEPROM 1KBIT 400KHZ 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5045-SS_EK_AB | 功能描述:AS5045 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:9V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5045 标准包装:1 |
| AS5045-SS_EK_DB | 功能描述:AS5045 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5045 标准包装:1 |
| AS5045TR | 制造商:AMSCO 制造商全称:austriamicrosystems AG 功能描述:12 BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER |
| AS5045-Z | 制造商:AMS 功能描述:0 |
| AS5046 | 制造商:AMS 功能描述:AS Series 360 3.3 to 5 V SMT Programmable Magnetic Angle Encoder - SSOP-16 制造商:AMS 功能描述:AS Series 360?3.3 to 5 V SMT Programmable Magnetic Angle Encoder - SSOP-16 |
发布紧急采购，3分钟左右您将得到回复。