- 您现在的位置：买卖IC网 > PDF目录17275 > AS5134 DB (ams)BOARD DEMO AS5134 PDF资料下载
参数资料
| 型号： | AS5134 DB |
| 厂商： | ams |
| 文件页数： | 23/33页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO AS5134 |
| 产品培训模块： | AS5134 Overview |
| 标准包装： | 1 |
| 传感器类型： | 磁性，旋转位置 |
| 传感范围： | 360° |
| 接口： | USB |
| 电源电压： | 5V USB 或 9V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，线缆 |
| 已用 IC / 零件： | AS5134 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
AS5134
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
Figure 17. OTP Programming Connection
Standard Case
Special Case
maximum
parasitic cable
inductance
V SUPPLY
V SUPPLY
V zapp
L<50nH
V prog
PROG
V DD
V zapp
L<50nH
V prog
PROG
V DD
C1
100nF
C2
10μF
GND
PROM Cell
C1
100nF
C2
10μF
GND
PROM Cell
Remove for normal operation
Note: The maximum capacitive load at PROG in normal operation is less than 20pF. However, during programming the capacitors C1+C2 are
needed to buffer the programming voltage during current spikes, but they must be removed for normal operation. To overcome this
contradiction, the recommendation is to add a diode (4148 or similar) between PROG and V DD as shown in Figure 17 (special case
setup), if the capacitors can not be removed at final assembly.
Due to D1, the capacitors C1+C2 are loaded with V DD -0.7V at startup, hence not influencing the readout of the internal OTP registers.
During programming the OTP, the diode ensures that no current is flowing from PROG (8-8.5V) to VDD (5V).
In the standard case (see Figure 17 ), the verification of a correct OTP readout can be done either by analog readback of the OTP reg-
ister or with the aid of the OTP_OK bit. The special case setup provides only the OTP_OK bit for verifying the correct reading of the
OTP. Analog readback is not usable in the special case mode, as the diode pulls the PROG pin to V DD .
The OTP_OK bit can be accessed with command #4 (see Table 9) .
As long as the PROG pin is accessible it is recommended to use standard setup. In case the PROG pin is not accessible at final
assembly, the special setup is recommended.
8.1.2
Programming Verification
After programming, the programmed OTP bits must be verified in two ways:
Digital Read Out (Mandatory): After sending a READ OTP command, the readback information must be the same as programmed
information. Otherwise, it indicates that the programming was not performed correctly.
Note: Either “Digital Verification” or “Analog Verification” must be carried out in addition to the “Digital Read Out”.
Digital Verification: Checking the OTP_OK bit (0 = OK, 1 = error)
i) At room temperature
ii) Right after the programming
Analog Verification: By switching into Extended Mode and sending a READ ANA command, the pin PROG becomes an output sending an
analog voltage with each clock representing a sequence of the bits in the OTP register (starting with D61). A voltage of <500mV indicates a
correctly programmed bit (“1”) while a voltage level between 2V and 3.5V indicates a correctly unprogrammed bit (“0”). Any voltage level in
between indicates incorrect programming.
www.austriamicrosystems.com/AS5134
Revision 2.3
22 - 32
相关PDF资料 |
PDF描述 |
|---|---|
| 592D226X0016D2W15H | CAP TANT 22UF 16V 20% 2917 |
| ECC20DCSH | CONN EDGECARD 40POS DIP .100 SLD |
| AIAP-02-121-K | INDUCTOR 120UH 10% 1.1A |
| MAX15023EVKIT+ | KIT EVALUATION FOR MAX15023 CTLR |
| 591D336X96R3B2T15H | CAP TANT 33UF 6.3V 10% 1611 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5134-PB | 功能描述:磁传感器开发工具 AS5134 Progamming Board RoHS:否 制造商:Maxim Integrated 工具用于评估: 接口类型: 工作电压: |
| AS5134-SS_EK_AB | 功能描述:AS5134 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:4.5 V ~ 5.5 V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5134 标准包装:1 |
| AS5134-SS_EK_DB | 功能描述:AS5134 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5134 标准包装:1 |
| AS5134-SS_EK_PB | 功能描述:AS5000 Programmer, AS5134 - ZIF Socket 制造商:ams 系列:- 零件状态:有效 模块/板类型:ZIF 插口 配套使用产品/相关产品:AS5000 编程器，AS5134 标准包装:1 |
| AS5134-ZSSM | 制造商:AMS 功能描述:IC ENCODER RPTARY 20-SSOP |
发布紧急采购，3分钟左右您将得到回复。