- 您现在的位置：买卖IC网 > PDF目录21914 > AS5140H-ASSU (ams)IC ENCODER PROG 10-BIT 16-SSOP PDF资料下载
参数资料
| 型号： | AS5140H-ASSU |
| 厂商： | ams |
| 文件页数： | 14/38页 |
| 文件大小： | 0K |
| 描述： | IC ENCODER PROG 10-BIT 16-SSOP |
| 应用说明： | AS5000 Series Magnet Selection Guide AS5000 Series Magnets for Extended Vertical Range |
| 标准包装： | 77 |
| 传感范围： | 45mT ~ 75mT |
| 类型： | 线性，旋转编码器 - 可编程 |
| 电源电压： | 3 V ~ 3.6 V，4.5 V ~ 5.5 V |
| 电流 - 电源： | 21mA |
| 电流 - 输出（最大）： | 4mA |
| 输出类型： | 数字式，PWM，10 位串行 |
| 特点： | 可编程 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 804 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
AS5140H
Data Sheet - D e t a i l e d D e s c r i p t i o n
Figure 5. Synchronous Serial Interface with Absolute Angular Position Data
CSn
t CLK FE
T CLK/2
t CSn
t CLK FE
CLK
1
8
16
1
DO
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
OCF COF
LIN
Mag Mag
INC DEC
Even
PAR
D9
t DO active
t DO valid
Angular Position Data
Status Bits
t DO Tristate
Data Content
D9:D0 – Absolute angular position data (MSB is clocked out first).
OCF – (Offset Compensation Finished). Logic high indicates the finished Offset Compensation Algorithm. For fast startup, this bit may be polled
by the external microcontroller. As soon as this bit is set, the AS5140H has completed the startup and the data is valid (see Table 17) .
COF – (Cordic Overflow). Logic high indicates an out of range error in the CORDIC part. When this bit is set, the data at D9:D0 is invalid. The
absolute output maintains the last valid angular value. This alarm may be resolved by bringing the magnet within the X-Y-Z tolerance limits.
LIN – (Linearity Alarm). Logic high indicates that the input field generates a critical output linearity. When this bit is set, the data at D9:D0 may still
be used, but can contain invalid data. This warning may be resolved by bringing the magnet within the X-Y-Z tolerance limits.
MagINCn – (Magnitude Increase) becomes HIGH, when the magnet is pushed towards the IC, thus increasing the magnetic field strength.
MagDECn – (Magnitude Decrease) becomes HIGH, when the magnet is pulled away from the IC, thus decreasing the magnetic field strength.
Signal “HIGH” for both MagINCn and MagDECn indicate a magnetic field that is out of the allowed range (see Table 16) .
Table 16. Magnetic Magnitude Variation Indicator
MagINCn
0
0
1
1
MagDECn
0
1
0
1
Description
No distance change
Magnetic Input Field OK (in range)
Distance increase: Pull-function. This state is dynamic, it is only active while the magnet
is moving away from the chip in Z-axis.
Distance decrease: Push- function. This state is dynamic, it is only active while the
magnet is moving towards the chip in Z.-axis.
Magnetic Input Field invalid – out of range: Too large, Too small (missing magnet).
Note: Pins 1 and 2 (MagINCn, MagDECn) are open drain outputs and require external pull-up resistors. If the magnetic field is in range, both
outputs are turned off.
The two pins may also be combined with a single pull-up resistor. In this case, the signal is high when the magnetic field is in range. It is low in all
other cases (see Table 16) .
Even Parity – A bit for transmission error detection of bits 1to 15 (D9 to D0, OCF, COF, LIN, MagINCn, MagDECn).
The absolute angular output is always set to a resolution of 10 bit. Placing the magnet above the chip, angular values increase in clockwise
direction by default. Data D9:D0 is valid, when the status bits have the following configurations:
Table 17. Status Bit Outputs
OCF
COF
LIN
MagINCn
MagDECn
Parity
0
0
1
0
0
0
1
even checksum of bits 1:15
1
0
www.austriamicrosystems.com/AS5140H
Revision 1.4
13 - 37
相关PDF资料 |
PDF描述 |
|---|---|
| D2HW-C262M | SUBMINIATURE BASIC SWITCH |
| A1354KKTTN-T | IC HALL EFFECT SENSOR 2WIRE 4SIP |
| D2HW-C261M | SUBMINIATURE BASIC SWITCH |
| ATS643LSHTN-I1-T | IC SENSOR GEAR TOOTH 4-SIP |
| D2HW-C233M | SUBMINIATURE BASIC SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5140H-DB | 制造商:ams 功能描述:AS5140H Demo Board |
| AS5140H-PB | 制造商:ams 功能描述:AS5140H Progamming Board |
| AS5140-SS_EK_AB | 功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:串行 灵敏度:- 电压 - 电源:5V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5140 标准包装:1 |
| AS5140-SS_EK_DB | 功能描述:AS5140 - Magnetic, Rotary Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，旋转位置 感应范围:360° 接口:USB 灵敏度:- 电压 - 电源:5V USB 或 9V 嵌入式:是，MCU，8 位 所含物品:板，线缆 使用的 IC/零件:AS5140 标准包装:1 |
| AS51430FLF | 制造商:TT Electronics / IRC 功能描述:AS51430FLF |
发布紧急采购，3分钟左右您将得到回复。