- 您现在的位置：买卖IC网 > Datasheet目录961 > AS5311 DB (ams)BOARD EVAL FOR AS5311 Datasheet资料下载
参数资料
| 型号： | AS5311 DB |
| 厂商： | ams |
| 文件页数： | 3/29页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AS5311 |
| 标准包装： | 1 |
| 传感器类型： | 磁性，线性位置 |
| 接口： | USB/串行 |
| 电源电压： | 3.3V，5V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板 |
| 已用 IC / 零件： | AS5311 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AS5311
Datasheet - P i n A s s i g n m e n t s
4 Pin Assignments
Figure 2. Pin Assignments (Top View)
NC
MagIncn
MagDecn
A
B
NC
Index
VSS
Prog
NC
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
NC
VDD5V
VDD3V3
NC
NC
PWM
CSn
CLK
DO
NC
4.1 Pin Descriptions
Pin 4(A), 5(B) and 7(Index) are the incremental outputs. The incremental output has a resolution of 10-bit per pole pair, resulting in a step length
of 1.95μm.
Note: Pin 14 (CSn) must be low to enable the incremental outputs.
Pins 12, 13 and 14 are used for serial data transfer. Chip Select (CSn; active low) initiates serial data transfer. CLK is the clock input and DO is
the data output. A logic high at CSn puts the data output pin (DO) to tri-state and terminates serial data transfer. CSn must be low to enable the
incremental outputs. See Section 7.1.1 for further options.
Pin 8 is the supply ground pin. Pins 18 and 19 are the positive supply pins.
For 5V operation, connect the 5V supply to pin 19 and add a 2μF…10μF buffer capacitor at pin 18.
For 3.3V operation, connect both pins 18 and 19 to the 3.3V supply.
Pin 9 is used for factory programming only. It should be connected to VSS.
Pins 2 and 3 are the magnetic field change indicators, MagINCn and MagDECn (magnetic field strength increase or decrease through variation
of the distance between the magnet and the device). These outputs can be used to detect the valid magnetic field range.
External pull-up resistors are required at these pins. See Section 6.2.2 for maximum output currents on these pins. Since they are open-drain
outputs they can also be combined (wired-and).
Pin 15 (PWM) allows a single wire output of the 12-bit absolute position value within one pole pair (2.0mm). The value is encoded into a pulse
width modulated signal with 1μs pulse width per step (1μs to 4097μs over one pole pair).
Pins 1, 6, 10, 11, 16, 17 and 20 are for internal use and must not be connected.
www.ams.com/AS5311
Revision 1.12
3 - 29
相关PDF资料 |
PDF描述 |
|---|---|
| ASEK712ELC-05B-T-DK | BOARD EVAL FOR ASEK712ELC-05B |
| ASPF240D3R | RELAY SSR 3A 240VAC SIP PHASE |
| ASX220A06 | RELAY TELECOM DPDT 10MA 6V |
| AT-C-26-4/4/B-10-OE-R | CORD COIL SGL END 4-4 BLACK 10' |
| AT-C-26-4/4/B-10/R-R | CORD COIL REVERSED 4-4 BLACK 10' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AS5311-TS_EK_AB | 功能描述:AS5311 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:串行 灵敏度:- 电压 - 电源:3 V ~ 5.5 V 嵌入式:否 所含物品:板 使用的 IC/零件:AS5311 标准包装:1 |
| AS5311-TS_EK_DB | 功能描述:AS5311 - Magnetic, Linear Position Sensor Evaluation Board 制造商:ams 系列:- 零件状态:有效 传感器类型:磁性，线性位置 感应范围:- 接口:USB 灵敏度:- 电压 - 电源:3.3V，5V 嵌入式:是，MCU，8 位 所含物品:板 使用的 IC/零件:AS5311 标准包装:1 |
| AS53160FLF | 制造商:TT Electronics / IRC 功能描述:AS53160FLF |
| AS53160HLF | 制造商:TT Electronics / IRC 功能描述:AS53160HLF |
| AS53160JLF | 制造商:TT Electronics / IRC 功能描述:AS53160JLF |
发布紧急采购，3分钟左右您将得到回复。