- 您现在的位置：买卖IC网 > Datasheet目录961 > ASEK712ELC-05B-T-DK (Allegro Microsystems Inc)BOARD EVAL FOR ASEK712ELC-05B Datasheet资料下载
参数资料
| 型号： | ASEK712ELC-05B-T-DK |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR ASEK712ELC-05B |
| 设计资源： | ACS7xx Demo Brd BOM/Schematics |
| 标准包装： | 1 |
| 传感器类型： | 电流传感器 |
| 传感范围： | -5 A ~ 5 A |
| 灵敏度： | 185mV/A |
| 电源电压： | 4.5 V ~ 5.5 V |
| 嵌入式： | 否 |
| 已供物品： | 板 |
| 已用 IC / 零件： | ASEK712ELC-05B |
| 其它名称： | 620-1431 |
ACS712
Fully Integrated, Hall Effect-Based Linear Current Sensor IC
with 2.1 kVRMS Isolation and a Low-Resistance Current Conductor
Improving Sensing System Accuracy Using the FILTER Pin
In low-frequency sensing applications, it is often advantageous
to add a simple RC filter to the output of the device. Such a low-
pass filter improves the signal-to-noise ratio, and therefore the
resolution, of the device output signal. However, the addition of
an RC filter to the output of a sensor IC can result in undesirable
device output attenuation — even for DC signals.
Signal attenuation, ? V ATT , is a result of the resistive divider
effect between the resistance of the external filter, R F (see
Application 6), and the input impedance and resistance of the
customer interface circuit, R INTFC . The transfer function of this
resistive divider is given by:
temperature. Therefore, signal attenuation will vary as a function
of temperature. Note that, in many cases, the input impedance,
R INTFC , of a typical analog-to-digital converter (ADC) can be as
low as 10 k Ω .
The ACS712 contains an internal resistor, a FILTER pin connec-
tion to the printed circuit board, and an internal buffer amplifier.
With this circuit architecture, users can implement a simple
RC filter via the addition of a capacitor, C F (see Application 7)
from the FILTER pin to ground. The buffer amplifier inside of
the ACS712 (located after the internal resistor and FILTER pin
? V ATT = V IOUT ?
?
?
?
?
R INTFC
R F + R INTFC
?
?
.
connection) eliminates the attenuation caused by the resistive
divider effect described in the equation for ? V ATT . Therefore, the
ACS712 device is ideal for use in high-accuracy applications
Even if R F and R INTFC are designed to match, the two individual
resistance values will most likely drift by different amounts over
+5 V
Pin 3 Pin 4
IP– IP–
that cannot afford the signal attenuation associated with the use
of an external RC low-pass filter.
VCC
Pin 8
Allegro ACS706
Application 6. When a low pass filter is constructed
externally to a standard Hall effect device, a resistive
divider may exist between the filter resistor, R F, and
the resistance of the customer interface circuit, R INTFC .
This resistive divider will cause excessive attenuation,
as given by the transfer function for ? V ATT .
0.1 F
Voltage
Regulator
Amp
To all subcircuits
Out
VIOUT
Pin 7
N.C.
Pin 6
R F
Resistive Divider
Input
Application
Interface
Circuit
Low Pass Filter
Gain
Temperature
Coefficient
Offset
C F
1 nF
R INTFC
Trim Control
+5 V
VCC
Pin 8
IP+ IP+
Pin 1 Pin 2
GND
Pin 5
Application 7. Using the FILTER pin
provided on the ACS712 eliminates the
attenuation effects of the resistor divider
Hall Current
Drive
Allegro ACS712
between R F and R INTFC , shown in Appli-
cation 6.
IP+
Pin 1
IP+
Pin 2
IP–
Pin 3
IP–
Pin 4
Sense Temperature
Coefficient Trim
Sense
Trim
Signal
Recovery
0 Ampere
Offset Adjust
Buffer Amplifier
and Resistor
VIOUT
Pin 7
Input
Application
Interface
Circuit
R INTFC
GND
FILTER
Pin 5
Pin 6
C F
1 nF
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
13
相关PDF资料 |
PDF描述 |
|---|---|
| ASPF240D3R | RELAY SSR 3A 240VAC SIP PHASE |
| ASX220A06 | RELAY TELECOM DPDT 10MA 6V |
| AT-C-26-4/4/B-10-OE-R | CORD COIL SGL END 4-4 BLACK 10' |
| AT-C-26-4/4/B-10/R-R | CORD COIL REVERSED 4-4 BLACK 10' |
| AT-C-26-4/4/B-10-R | CORD COIL STANDARD 4-4 BLACK 10' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ASEK712ELC-20A-T-DK | 功能描述:BOARD EVAL FOR ASEK712ELC-20A RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ASEK712ELC-30A-T-DK | 功能描述:BOARD EVAL FOR ASEK712ELC-30A RoHS:是 类别:编程器，开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- |
| ASEK713ELC-20A-T-DK | 功能描述:ACS713 - Current Sensor Sensor Evaluation Board 制造商:allegro microsystems, llc 系列:- 零件状态:有效 传感器类型:电流传感器 感应范围:20A 接口:- 灵敏度:185mV/A 电压 - 电源:4.5 V ~ 5.5 V 嵌入式:- 所含物品:板 使用的 IC/零件:ACS713 标准包装:1 |
| ASEK713ELC-30A-T-DK | 功能描述:KIT EVALUATION SENSOR 制造商:allegro microsystems, llc 系列:* 零件状态:在售 标准包装:1 |
| ASEK716KLA-12CB-T-DK | 功能描述:ACS716 - Current Sensor Sensor Evaluation Board 制造商:allegro microsystems, llc 系列:- 零件状态:有效 传感器类型:电流传感器 感应范围:12.5A 接口:- 灵敏度:37.1mV/A 电压 - 电源:3 V ~ 3.6 V 嵌入式:- 所含物品:板 使用的 IC/零件:ACS716 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。