- 您现在的位置：买卖IC网 > PDF目录18888 > ASQ10418 (Panasonic Electric Works)SWITCH SNAP LEVER SPDT .1A SLD PDF资料下载
参数资料
| 型号： | ASQ10418 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 9/10页 |
| 文件大小： | 0K |
| 描述： | SWITCH SNAP LEVER SPDT .1A SLD |
| 标准包装： | 1,000 |
| 系列： | ASQ1 |
| 电路： | 单刀双掷 |
| 开关功能： | 开-瞬时 |
| 触点额定电压： | 0.1A @ 30VDC |
| 触动器类型： | 按片，仿真滚轴 |
| 安装类型： | 底座安装 |
| 端接类型： | 焊片 |
| 操作力： | 150gf |
ASQ1
6. Wire leads left side type: Mounting hole 3mm, standard type
mm General tolerance: ±0.25
CAD Data
R 0.5
C 0.3
1.9 dia.
8.4 ± 0.2
5.4 ± 0.15
2.7
5.4
13.3
3.2 ± 0.1
?
3.0 + 0.1
5.1 5.9
R 0.5
4.5
1.4 dia.
8.3 ± 0.1
3.7
4.3
5.2
5.0 ± 2
300 ± 10
R 0.5
2.4
3.0 + ? 0 0.1 dia.
? Wire lead thickness :
0.3mm 2
NOTES
Wire lead color
:
:
:
COM ···· Black
NC ······· Red
NO ······· White
1. Soldering conditions
1) To secure the switch, please use an
Plunger/Lever pushed
The application of excessive heat upon
the switch when soldering can cause
degradation of switch operation.
Therefore, be sure to keep within the
conditions given below.
1) Manual soldering: use soldering irons
(max. 350°C, within 3 seconds) capable
of temperature adjustment. This is to
M3 small screw on a ?at surface and
tighten using a maximum torque of 0.29
N·m. It is recommended that spring
washers be used with the screws and
adhesive be applied to lock the screws to
prevent loosening of the screws. Please
make sure not to apply adhesive onto the
moving parts.
Actuator
Pin
plunger
Leaf lever
Simulated
leaf lever
From mounting
boss and hole
center line
7.8 to 5.9
8.4 to 6.2
11.1 to 8.7
From standoff
12.0 to 10.1
12.6 to 10.4
15.3 to 12.9
prevent deterioration due to soldering
heat. Care should be taken not to apply
force to the terminals during soldering.
2) Automatic soldering: Soldering must
be done as below;
260°C: within 6 seconds
350°C: within 3 seconds
2. Mounting
Please avoid use in which load would be
applied to the sides (hatch part (both
sides) shown below) of the switch in the
direction indicated by the arrows. This
could cause erroneous operation. Also,
when using a metal installation board,
please make allowance for burr direction
designation and burr suppressing, etc.,
so that the burr side will not be on the
2) Be sure to maintain adequate
insulating clearance between each
terminal and ground.
3) Although it is possible to directly
operate the pin plunger type from the
lateral direction, please consult us if
doing so.
4) After mounting please make sure no
tensile load will be applied to the switch
terminals.
5) Range of possible use: Please set the
operation position to within the ranges in
the following table so that there is
suf?cient insulation distance and to
maintain contact reliability.
mm
Plunger/lever free
6) PC board terminal type should be
used if the products are to be soldered on
the PC board. Solder terminal type is not
for soldering on PC board.
3. Cautions regarding the circuit
1) In order to prevent malfunction in set
devices caused by bounce and chattering
during the ON-OFF switch operation,
please verify the validity of the circuit
under actual operating conditions and
temperature range.
2) When switching inductive loads
(relays, solenoids, buzzers, etc.), an arc
absorbing circuit is recommended to
protect the contacts.
4. Please verify under actual
conditions.
switch installation side.
Actuator
Pin
plunger
Leaf lever
Simulated
leaf lever
From mounting
boss and hole
center line
>9.2
>10.7
>13.5
From standoff
>13.4
>14.9
>17.7
Please be sure to conduct quality
veri?cation under actual operating
conditions in order to increase reliability
during actual use.
5. Switch selection
Please make your selection so that there
will be no problems even if the operating
characteristics vary up to ±20% from the
standard values.
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e
AECTB6E 201201-T
相关PDF资料 |
PDF描述 |
|---|---|
| ASVMB-3.6864MHZ-LY-T | OSC MEMS 3.6864 MHZ SMD |
| 2194AX4-28V | LAMP NEON INCAND WHITE PNL MNT |
| 2194AX5-28V | LAMP NEON INCAND GREEN PNL MNT |
| D3V-11G3-1C23-K | SWITCH LEVER SPDT 11A QC TERM |
| 2194A4-28V | LAMP WHITE 28V PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ASQ10610 | 制造商:Panasonic Electric Works 功能描述:Switch Snap Action N.O./N.C. SPDT Pin Plunger Wire Lead 0.1A 30VDC 1.5N Screw Mount 制造商:Panasonic Electric Works 功能描述:Switch,pin plunger,SPDT,bottom wire tm |
| ASQ10610J | 制造商:Panasonic Electric Works 功能描述: |
| ASQ10617 | 制造商:Panasonic Electric Works 功能描述:Switch,leaf lever,SPDT,bottom wire tm |
| ASQ10618 | 制造商:Panasonic Electric Works 功能描述: 制造商:Panasonic Electric Works 功能描述:Switch,sim leaf levr,SPDT,bottom wire tm |
| ASQ10620 | 制造商:Panasonic Electric Works 功能描述:MICROSWITCH PLUNGER 制造商:Panasonic Electric Works 功能描述:MICROSWITCH, PLUNGER 制造商:Panasonic Electric Works 功能描述:MICROSWITCH, PLUNGER; Contact Configuration:SPST-NC; Microswitch Type:Snap Action; Actuator Style:Pin Plunger; Switch Operation:-; Operating Force Max:1.5N; Contact Voltage DC Nom:30V; Contact Current Max:100mA; Switch Terminals:Wire;RoHS Compliant: Yes 制造商:Panasonic Electric Works 功能描述:Switch,pin plungr,SPST-NC,bottom wire tm |
发布紧急采购，3分钟左右您将得到回复。