- 您现在的位置：买卖IC网 > PDF目录223398 > ASQ48T15033-PBB0G (POWER-ONE INC) 1-OUTPUT 49.5 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | ASQ48T15033-PBB0G |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 49.5 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT, ONE-EIGHTH BRICK PACKAGE-8 |
| 文件页数： | 12/15页 |
| 文件大小： | 267K |
| 代理商： | ASQ48T15033-PBB0G |
MCD10170 Rev. 1.0, 10-Jun-10
Page 6 of 15
www.power-one.com
ASQ48T15033 & ASQ48S15033 DC-DC Converter Data Sheet
36 to 75 VDC Input; 15A, 3.3 VDC Output
Operation
Input and Output Impedance
These power converters have been designed to be stable
with no external capacitors when used in low inductance in-
put and output circuits.
However, in many applications, the inductance associated
with the distribution from the power source to the input of the
converter can affect the stability of the converter. The addi-
tion of a 33 F electrolytic capacitor with an ESR < 1
across the input helps ensure stability of the converter. In
many applications, the user has to use decoupling capacit-
ance at the load. The power converter will exhibit stable
operation with external load capacitance up to 15,000 F.
ON/OFF (Pin 2)
The ON/OFF pin is used to turn the power converter on or
off remotely via a system signal. There are two remote con-
trol options available, positive logic and negative logic and
both are referenced to Vin(-). Typical connections are shown
in Fig. 2.
Rload
Vin
CONTROL
INPUT
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
Converter
Semi
QTM Family
Fig. 2: Circuit configuration for ON/OFF function.
The positive logic version turns on when the ON/OFF pin is
at a logic high and turns off when at a logic low. The conver-
ter is on when the ON/OFF pin is left open
.
The negative logic version turns on when the pin is at a logic
low and turns off when the pin is at a logic high. The
ON/OFF pin can be hard wired directly to Vin(-) to enable
automatic power up of the converter without the need of an
external control signal.
ON/OFF pin is internally pulled-up to 5 V through a resistor.
A mechanical switch, open collector transistor, or FET can
be used to drive the input of the ON/OFF pin. The device
must be capable of sinking up to 0.2 mA at a low level vol-
tage of
0.8 V. An external voltage source (±20 V maxi-
mum) may be connected directly to the ON/OFF input, in
which case it must be capable of sourcing or sinking (de-
pending on the signal polarity) up to 1 mA. See the Start-up
Information section for system timing waveforms associated
with use of the ON/OFF pin.
Remote Sense (Pins 5 and 7)
The remote sense feature of the converter compensates for
voltage drops occurring between the output pins of the con-
verter and the load. The SENSE(-) (Pin 5) and SENSE(+)
(Pin 7) pins should be connected at the load or at the point
where regulation is required (see Fig. 3).
100
10
Rw
Rload
Vin
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
Converter
Semi
QTM Family
Fig. 3: Remote sense circuit configuration.
If remote sensing is not required, the SENSE(-) pin must be
connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin
must be connected to the Vout(+) pin (Pin 8) to ensure the
converter will regulate at the specified output voltage. If
these connections are not made, the converter will deliver an
output voltage that is slightly higher than the specified value.
Because the sense leads carry minimal current, large traces
on the end-user board are not required. However, sense
traces should be located close to a ground plane to minimize
system noise and insure optimum performance. When wiring
discretely, twisted pair wires should be used to connect the
sense lines to the load to reduce susceptibility to noise.
The converter’s output over-voltage protection (OVP) senses
the voltage across Vout(+) and Vout(-), and not across the
sense lines, so the resistance (and resulting voltage drop)
between the output pins of the converter and the load should
be minimized to prevent unwanted triggering of the OVP.
When utilizing the remote sense feature, care must be taken
not to exceed the maximum allowable output power capabili-
ty of the converter, equal to the product of the nominal out-
put voltage and the allowable output current for the given
conditions.
When using remote sense, the output voltage at the conver-
ter can be increased by as much as 10% above the nominal
相关PDF资料 |
PDF描述 |
|---|---|
| ASR303.825A01-SE | 1-PORT SAW RESONATOR, 303.825 MHz |
| ASR310E | 1-PORT SAW RESONATOR, 310 MHz |
| ASR310S2 | 1-PORT SAW RESONATOR, 310 MHz |
| ASR315EA | 1-PORT SAW RESONATOR, 315 MHz |
| ASR315S2 | 1-PORT SAW RESONATOR, 315 MHz |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ASQ48T15033-PBC0 | 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 3.3V 15A - Bulk |
| ASQ530F-02-06S | 制造商:SMC Corporation of America 功能描述:Air saving valve port size 1/4 |
| ASQ530F-02-08S | 制造商:SMC 功能描述:Air saving valve port size 1/4 |
| ASQ530F-03-08S | 制造商:SMC 功能描述:Air saving valve port size 3/8 |
| ASQ530F-03-10S | 制造商:SMC 功能描述:Air saving valve port size 3/8 |
发布紧急采购，3分钟左右您将得到回复。