- 您现在的位置：买卖IC网 > PDF目录17852 > AT112 (NKK Switches)WRENCH SOCKET FOR LB SERIES PDF资料下载
参数资料
| 型号： | AT112 |
| 厂商： | NKK Switches |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | WRENCH SOCKET FOR LB SERIES |
| 产品培训模块： | Switch Basics |
| 标准包装： | 1 |
Series LB
ASSEMBLY INSTRUCTIONS
Lamp Installation & LED Orientation
Standard Size Pushbuttons
D
Incandescent & Neon Lamps
AT607 & AT607N
Align projections on lamp
with grooves (B) in holder
when inserting lamp. To
correctly join the lamp
holder and cap base,
match the cut corners (A).
B
Bright LED AT627
Panel Seal Models Snap-in Models
For panel seal models, For snap-in models,
Bright LED must first be Bright LED must be
inserted into the lamp inserted into the cap
socket which is built into first. Align cut corners
the switch. The cap can (C) when
then be placed on the inserting
switch. the LED.
Bright & Super Bright LEDs
AT625, AT631, AT632,
AT635
Align D-flat on LED with flat (B) in
holder when inserting the LED.
To correctly join the lamp holder and
cap base, match the cut corners (A).
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
B
A
LED
A
B
C
LED
D Flat
Switch & Cap Assembly
C
Round & Rectangular
Match clip on cap assembly with receptacle inside
switch. Lamp terminals will then be aligned correctly
with lamp socket.
Cut Corner
Rubber Seal
Projection
C
Square
Match projection (C) on cap
assembly with groove (C)
inside switch. Lamp terminals
will then be aligned correctly
with lamp socket.
Installation & Maintenance
Projection
Notch
Panel Seal
With Lamps AT607, AT607N, and
LEDs AT614, AT625, AT631, AT632:
Match projection on cap assembly with
notch inside switch. Lamp terminals
will then be aligned correctly with lamp
socket.
panel. Snap
Actuator must be in UP position.
Replace lamp and reassemble as
shown above.
Snap-in Mount
Snap-in clip holds all switches firmly
in place.
To mount round
switch, match
the antirotation Projection
projection on
switch with
guide cut in
Panel
into panel
cutout.
D64
Panel Seal
Bushing Mount
Insert switch from the
front of the panel with
the o-ring between the
built-in bezel and the
panel. Install mounting
nut AT075 (supplied with
switch) from the rear of
the panel.
Overtightening mounting
nut may damage the
switch housing.
www.nkk.com
Lamp Replacement
Bezel
O-ring
Pull off cap with cap extractor
AT109.
Panel
Mounting Nut
AT109 AT112
Cap Extractor Socket Wrench
相关PDF资料 |
PDF描述 |
|---|---|
| TC33X-2-101G | TRIMMER 100 OHM 0.1W SMD |
| 170824J250NF | CAP FILM 0.82UF 250VDC AXIAL |
| JJC0E156MELZ | CAP SUPER 15F 2.5V SNAP |
| TC33X-1-202E | TRIMMER 2K OHM 0.1W SMD |
| 170824J160JE | CAP FILM 0.82UF 160VDC AXIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT-112 | 制造商:HRS 制造商全称:HRS 功能描述:Fixed Attenuators (SMA Type) |
| AT-112(40) | 功能描述:衰减器 -互连 RoHS:否 制造商:Pomona Electronics 最大衰减: 容差: 频率范围:DC to 500 MHz 阻抗:50 Ohms 功率额定值:2 W 端接类型:Crimp 连接器类型:BNC Male / Female 工作温度范围:0 C to + 102 C |
| AT-1120 | 制造商:HRS 制造商全称:HRS 功能描述:High Power Fixed Attenuators (Radiator built-in) |
| AT-1120(40) | 功能描述:衰减器 -互连 RoHS:否 制造商:Pomona Electronics 最大衰减: 容差: 频率范围:DC to 500 MHz 阻抗:50 Ohms 功率额定值:2 W 端接类型:Crimp 连接器类型:BNC Male / Female 工作温度范围:0 C to + 102 C |
| AT-11233 | 功能描述:拨动开关 Sealed OI RoHS:否 制造商:C&K Components 触点形式:DPDT 开关功能:ON - ON - ON 电流额定值: 电压额定值 AC:20 V 电压额定值 DC:20 V 功率额定值:0.4 VA 端接类型:V-Bracket 安装风格: 端子密封:Epoxy 触点电镀:Gold 照明:Not Illuminated |
发布紧急采购，3分钟左右您将得到回复。