- 您现在的位置：买卖IC网 > PDF目录166372 > AT24C256C-TH-B (ATMEL CORP) 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 PDF资料下载
参数资料
| 型号： | AT24C256C-TH-B |
| 厂商： | ATMEL CORP |
| 元件分类： | PROM |
| 英文描述： | 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| 封装： | 4.40 MM, LEAD AND HALOGEN FREE, PLASTIC, MO-153AA, TSSOP-8 |
| 文件页数： | 2/23页 |
| 文件大小： | 412K |
| 代理商： | AT24C256C-TH-B |
10
AT24C256C
8568A–SEEPR–11/08
5.
Write Operations
BYTE WRITE: A write operation requires two 8-bit data word addresses following the device address word and
acknowledgment. Upon receipt of this address, the EEPROM will again respond with a “0” and then clock in the first
8-bit data word. Following receipt of the 8-bit data word, the EEPROM will output a “0”. The addressing device, such as
a microcontroller, must then terminate the write sequence with a stop condition. At this time the EEPROM enters an
internally-timed write cycle, t
WR,
to the nonvolatile memory. All inputs are disabled during this write cycle and the
EEPROM will not respond until the write is complete (refer to Figure 9).
Figure 9.
Byte Write
Note:
* = DON’T CARE bit
PAGE WRITE: The 256K EEPROM is capable of 64-byte page writes.
A page write is initiated the same way as a byte write, but the microcontroller does not send a stop condition after the
first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller
can transmit up to 63 more data words. The EEPROM will respond with a “0” after each data word received. The
microcontroller must terminate the page write sequence with a stop condition (refer to Figure 10).
Figure 10.
Page Write
Note:
* = DON’T CARE bit
The data word address lower six bits are internally incremented following the receipt of each data word. The higher
data word address bits are not incremented, retaining the memory page row location. When the word address,
internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If
more than 64 data words are transmitted to the EEPROM, the data word address will “roll over” and previous data will
be overwritten. The address “roll over” during write is from the last byte of the current page to the first byte of the same
page.
ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled,
acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The
read/write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM
respond with a “0”, allowing the read or write sequence to continue.
相关PDF资料 |
PDF描述 |
|---|---|
| AT24C256CW-SH-B | 32K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| AT25256B-SSHL-T | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| AT25C02-10PC-2.7 | 256 X 8 SPI BUS SERIAL EEPROM, PDIP8 |
| AT27C010-17DI | 128K X 8 UVPROM, 170 ns, CDIP32 |
| AT27C010L-17KM | 128K X 8 UVPROM, 170 ns, CQCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT24C256C-XHLAU-B | 制造商:Atmel Corporation 功能描述:SERIAL EEPROM, 256K (32K X 8), 2-WI - 8 TSSOP, PB/HALO FREE - Bulk |
| AT24C256C-XHL-B | 功能描述:电可擦除可编程只读存储器 256K (32K X 8), 2-WI 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT24C256C-XHL-T | 功能描述:电可擦除可编程只读存储器 256K (32K X 8), 2-WI 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT24C256C-XPD-T | 制造商:Atmel Corporation 功能描述:SERIAL EEPROM, 256K (32K X 8) - Tape and Reel |
| AT24C256N-10SC | 功能描述:IC EEPROM 256KBIT 1MHZ 8SOIC 制造商:microchip technology 系列:- 包装:管件 零件状态:停產 存储器类型:非易失 存储器格式:EEPROM 技术:EEPROM 存储容量:256Kb （32K x 8） 时钟频率:1MHz 写周期时间 - 字，页:10ms 访问时间:550ns 存储器接口:I2C 电压 - 电源:4.5 V ~ 5.5 V 工作温度:0°C ~ 70°C（TA） 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 基本零件编号:AT24C256 标准包装:100 |
发布紧急采购，3分钟左右您将得到回复。