参数资料
型号: AT25080B-XHL-T
厂商: Atmel
文件页数: 5/26页
文件大小: 0K
描述: IC EEPROM 8KBIT 20MHZ 8TSSOP
标准包装: 1
格式 - 存储器: EEPROMs - 串行
存储器类型: EEPROM
存储容量: 8K (1K x 8)
速度: 5MHz,10MHz,20MHz
接口: SPI 3 线串行
电源电压: 1.8 V ~ 5.5 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 8-TSSOP
包装: 剪切带 (CT)
其它名称: AT25080B-XHL-TCT
AT25080B/160B
Table 2-3.
AC Characteristics (Continued)
Applicable over recommended operating range from T AI = – 40 ? C to +85 ? C, V CC = As Specified,
CL = 1 TTL Gate and 30pF (unless otherwise noted)
Symbol
Parameter
Voltage
Min
Max
Units
4.5–5.5
0
25
t LZ
HOLD to Output Low Z
2.5–5.5
0
50
ns
1.8–5.5
4.5–5.5
0
100
40
t HZ
HOLD to Output High Z
2.5–5.5
80
ns
1.8–5.5
4.5–5.5
200
40
t DIS
Output Disable Time
2.5–5.5
80
ns
1.8–5.5
4.5–5.5
200
5
t WC
Write Cycle Time
2.5–5.5
5
ms
1.8–5.5
5
Endurance (1)
3.3V, 25°C, Page Mode
1M
Write Cycles
Note:
3.
1. This parameter is characterized and is not 100% tested
Serial Interface Description
MASTER: The device that generates the serial clock.
SLAVE: Because the Serial Clock pin (SCK) is always an input, the AT25080B/160B always operates as a slave.
TRANSMITTER/RECEIVER: The AT25080B/160B has separate pins designated for data transmission (SO) and
reception (SI).
MSB: The Most Significant Bit (MSB) is the first bit transmitted and received.
SERIAL OP-CODE: After the device is selected with CS going low, the first byte will be received. This byte con-
tains the op-code that defines the operations to be performed.
INVALID OP-CODE: If an invalid op-code is received, no data will be shifted into th e AT25080B/160B, and the
serial output pin (SO) will remain in a high impedance state until the falling edge of CS is detected again. This will
reinitialize the serial communication.
CHIP SELECT: The AT25080B/160B is selected when the CS pin is low. When the device is not selected, data will
not be accepted via the SI pin, and the serial output pin (SO) will remain in a high impedance state.
HOLD: The HOLD pin is used in conjunction with the CS pin to select the AT25080B/160B. When the device is
selected and a serial sequence is underway, HOLD can be used to pause the serial communication with the mas-
ter device without resetting the serial sequence. To pause, the HOLD pin must be brought low while the SCK pin is
low. To resume serial communication, the HOLD pin is brought high while the SCK pin is low (SCK may still toggle
during HOLD). Inputs to the SI pin will be ignored while the SO pin is in the high impedance state.
WRITE PROTECT: The write protect pin (WP) will allow normal read/write operations when held high. When the
WP pin is brought low and WPEN bit is “1”, all write operations to the status register are inhibited. WP going low
while CS is still low will interrupt a write to the status register. If the internal write cycle has already been initiated,
WP going low will have no effect on any write operation to the status register. The WP pin function is blocked when
the WPEN bit in the status register is “0”. This will allow the user to install t h e AT25080B/160B in a system with the
WP pin tied to ground and still be able to write to the status register. All WP pin functions are enabled when the
WPEN bit is set to “1”.
5
5228E–SEEPR–3/12
相关PDF资料
PDF描述
24LC16BHT-I/MNY IC EEPROM 16KBIT 400KHZ 8TDFN
M1A3PE1500-2FG484 IC FPGA 1KB FLASH 1.5M 484-FBGA
M1A3PE1500-2FGG484 IC FPGA 1KB FLASH 1.5M 484-FBGA
APA450-FG256 IC FPGA PROASIC+ 450K 256-FBGA
ASC36DRYI-S93 CONN EDGECARD 72POS DIP .100 SLD
相关代理商/技术参数
参数描述
AT25080BY6-YH-T 功能描述:电可擦除可编程只读存储器 Serial 电可擦除可编程只读存储器 8K, Mini Map, 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25080N-10SA-2.7C 制造商:未知厂家 制造商全称:未知厂家 功能描述:SERIAL EEPROM|1KX8|CMOS|SOP|8PIN|PLASTIC
AT25080N-10SA-5.0C 制造商:未知厂家 制造商全称:未知厂家 功能描述:SERIAL EEPROM|1KX8|CMOS|SOP|8PIN|PLASTIC
AT25080N10SC 制造商:Atmel Corporation 功能描述:
AT25080N-10SC 制造商:Atmel Corporation 功能描述:EEPROM Serial-SPI 8K-Bit 1K x 8 5V 8-Pin SOIC