参数资料
型号: AT25256B-SSHL-T
厂商: Atmel
文件页数: 8/24页
文件大小: 0K
描述: IC EEPROM 256KBIT 20MHZ 8SOIC
标准包装: 1
格式 - 存储器: EEPROMs - 串行
存储器类型: EEPROM
存储容量: 256K (32K x 8)
速度: 5MHz,10MHz,20MHz
接口: SPI 3 线串行
电源电压: 1.8 V ~ 5.5 V
工作温度: -40°C ~ 85°C
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SOIC
包装: 剪切带 (CT)
其它名称: AT25256B-SSHL-TCT
WRITE STATUS REGISTER (WRSR): The WRSR instruction allows the user to select one of four levels of protection.
The Atmel ? AT25128B/256B is divided into four array segments. Top quarter (1/4), top half (1/2), or all of the mem-
ory segments can be protected. Any of the data within any selected segment will therefore be read only. The block
write protection levels and corresponding status register control bits are shown in Table 3-4 .
The three bits, BP0, BP1, and WPEN are nonvolatile cells that have the same properties and functions as the reg-
ular memory cells (e.g. WREN, t WC , RDSR)
Table 3-4.
Block Write Protect Bits.
Level
Status Register Bits
Array Addresses Protected
BP1
BP0
Atmel AT25128B
Atmel AT25256B
0
1 (1/4)
2 (1/2)
3 (All)
0
0
1
1
0
1
0
1
None
3000 – 3FFF
2000 – 3FFF
0000 – 3FFF
None
6000 – 7FFF
4000 – 7FFF
0000 – 7FFF
The WRSR instruction also allows the user to enable or disable the write protect (WP) pin through the use of the
write protect enable (WPEN) bit. Hardware write protection is enabled when the WP pin is low and the WPEN bit is
“1”. Hardware write protection is disabled when either the WP pin is high or the WPEN bit is “0”. When the device is
hardware write protected, writes to the Status Register, including the Block Protect bits and the WPEN bit, and the
blockprotected sections in the memory array are disabled. Writes are only allowed to sections of the memory which
are not block-protected.
Note:
When the WPEN bit is hardware write protected, it cannot be changed back to “0”, as long as the WP pin is held low
Table 3-5.
WPEN Operation
Unprotected
WPEN
0
0
1
1
X
X
WP
X
X
Low
Low
High
High
WEN
0
1
0
1
0
1
Protected Blocks
Protected
Protected
Protected
Protected
Protected
Protected
Blocks
Protected
Writable
Protected
Writable
Protected
Writable
Status Register
Protected
Writable
Protected
Protected
Protected
Writable
READ SEQUENCE (READ): Reading the AT25128B/256B via the SO pin requires the following sequence. After
the CS line is pulled low to select a device, the Read op-code is transmitted via the SI line followed by the byte
address to be read ( Table 3-6 ). Upon completion, any data on the SI line will be ignored. The data (D7 - D0) at the
specified address is then shifted out onto the SO line. If only one byte is to be read, the CS line should be driven
high after the data comes out. The read sequence can be continued since the byte address is automatically incre-
mented and data will continue to be shifted out. When the highest address is reached, the address counter will roll
over to the lowest address allowing the entire memory to be read in one continuous read cycle.
8
Atmel AT25128B/256B
8698C–SEEPR–8/11
相关PDF资料
PDF描述
AMM24DTKI CONN EDGECARD 48POS DIP .156 SLD
AGL1000V2-FG144I IC FPGA 1KB FLASH 1M 144FBGA
AGL1000V2-FGG144I IC FPGA 1KB FLASH 1M 144FBGA
A42MX24-2PQ160I IC FPGA MX SGL CHIP 36K 160-PQFP
AMM22DTBS-S189 CONN EDGECARD 44POS R/A .156 SLD
相关代理商/技术参数
参数描述
AT25256B-SSHL-T SL901 制造商:Atmel Corporation 功能描述:IC EEPROM 256KBIT 20MHZ 8SOIC
AT25256B-SSHL-T 制造商:Atmel Corporation 功能描述:Serial EEPROM IC
AT25256B-XHL-B 功能描述:电可擦除可编程只读存储器 256Kbit; SPI Bus High Spd; Mode 0 & 3 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25256B-XHL-T 功能描述:电可擦除可编程只读存储器 256Kbit; SPI Bus High Spd; Mode 0 & 3 RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
AT25256B-XHL-T SL901 制造商:Atmel Corporation 功能描述:IC EEPROM 256KBIT 20MHZ 8TSSOP