- 您现在的位置：买卖IC网 > PDF目录20472 > AT25320A-10PU-1.8 (Atmel)IC EEPROM 32KBIT 20MHZ 8DIP PDF资料下载
参数资料
| 型号： | AT25320A-10PU-1.8 |
| 厂商： | Atmel |
| 文件页数： | 11/26页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 32KBIT 20MHZ 8DIP |
| 标准包装： | 50 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 32K (4K x 8) |
| 速度： | 5MHz，10MHz，20MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
AT25080A/160A/320A/640A
Table 3-5.
WPEN Operation
Protected
Unprotected
Status
WPEN
0
0
1
1
X
X
WP
X
X
Low
Low
High
High
WEN
0
1
0
1
0
1
Blocks
Protected
Protected
Protected
Protected
Protected
Protected
Blocks
Protected
Writeable
Protected
Writeable
Protected
Writeable
Register
Protected
Writeable
Protected
Protected
Protected
Writeable
READ SEQUENCE (READ): Reading the AT25080A/160A/320A/640A via the Serial Output
(SO) pin requires the following sequence. After the CS line is pulled low to select a device, the
read op-code is transmitted via the SI line followed by the byte address to be read (A15 – A0, see
Table 3-6 ). Upon completion, any data on the SI line will be ignored. The data (D7 – D0) at the
specified address is then shifted out onto the SO line. If only one byte is to be read, the CS line
should be driven high after the data comes out. The read sequence can be continued since the
byte address is automatically incremented and data will continue to be shifted out. When the
highest address is reached, the address counter will roll over to the lowest address allowing the
entire memory to be read in one continuous read cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25080A/160A/320A/640A, two sepa-
rate instructions must be executed. First, the device must be write enabled via the WREN
instruction. Then a write (WRITE) instruction may be executed. Also, the address of the memory
location(s) to be programmed must be outside the protected address field location selected by
the block write protection level. During an internal write cycle, all commands will be ignored
except the RDSR instruction.
A write instruction requires the following sequence. After the CS line is pulled low to select the
device, the WRITE op-code is transmitted via the SI line followed by the byte address (A15 – A0)
and the data (D7 – D0) to be programmed (see Table 3-6 ). Programming will start after the CS pin
is brought high. The low-to-high transition of the CS pin must occur during the SCK low-time
immediately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a read status register
(RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”, the write cycle
has ended. Only the RDSR instruction is enabled during the write programming cycle.
The AT25080A/160A/320A/640A is capable of a 32-byte page write operation. After each byte of
data is received, the five low-order address bits are internally incremented by one; the high-
order bits of the address will remain constant. If more than 32 bytes of data are transmitted, the
address counter will roll over and the previously written data will be overwritten. The
AT25080A/160A/320A/640A is automatically returned to the write disable state at the comple-
tion of a write cycle.
NOTE: If the device is not write-enabled (WREN), the device will ignore the write instruction and
will return to the standby state, when CS is brought high. A new CS falling edge is required to
reinitiate the serial communication.
11
3347L–SEEPR–06/07
相关PDF资料 |
PDF描述 |
|---|---|
| 1SMA5916BT3G | DIODE ZENER 4.3V 1.5W SMA |
| SDR0403-3R3ML | INDUCTOR POWER 3.3UH 2.15A 0403 |
| VI-B2W-CX-F1 | CONVERTER MOD DC/DC 5.5V 75W |
| T95V335M020LSAL | CAP TANT 3.3UF 20V 20% 1410 |
| AT25256AW-10SU-2.7 | IC EEPROM 256KBIT 20MHZ 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT25320A-10PU-2.7 | 功能描述:电可擦除可编程只读存储器 32K(4K X 8) SPI 1M CYCLES - 10MS 2.7V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT25320A-10TI-1.8 | 功能描述:IC EEPROM 32KBIT 20MHZ 8TSSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT25320A-10TI-2.7 | 功能描述:IC EEPROM 32KBIT 20MHZ 8TSSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT25320A-10TQ-2.7 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25320A-10TU-1.8 | 功能描述:电可擦除可编程只读存储器 32K(4K X 8) SPI 1M CYCLES - 10MS 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
发布紧急采购，3分钟左右您将得到回复。