- 您现在的位置：买卖IC网 > PDF目录362471 > AT27BV040-12DI x8 EPROM PDF资料下载
参数资料
| 型号： | AT27BV040-12DI |
| 英文描述： | x8 EPROM |
| 中文描述： | x8存储器 |
| 文件页数： | 2/12页 |
| 文件大小： | 138K |
| 代理商： | AT27BV040-12DI |
AT27BV010
2
Atmel’s innovative design techniques provide fast speeds
that rival 5V parts while keeping the low power consump-
tion of a 3V supply. At V
CC
= 2.7V, any byte can be
accessed in less than 90 ns. With a typical power draw of
only 18 mW at 5 MHz and V
CC
= 3V, the AT27BV010 con-
sumes less than one fifth the power of a standard 5V
EPROM. Standby mode supply current is typically less
than 1
μ
A at 3V. The AT27BV010 simplifies system design
and stretches battery lifetime even further by eliminating
the need for power supply regulation.
The AT27BV010 is available in industry standard JEDEC-
approved one-time programmable (OTP) plastic PLCC,
TSOP, and VSOP packages. All devices feature two-line
control (CE, OE) to give designers the flexibility to prevent
bus contention.
The AT27BV010 operating with V
CC
at 3.0V produces TTL
level outputs that are compatible with standard TTL logic
devices operating at V
CC
= 5.0V. At V
CC
= 2.7V, the part is
compatible with JEDEC approved low voltage battery oper-
ation (LVBO) interface specifications. The device is also
capable of standard 5-volt operation making it ideally suited
for dual supply range systems or card products that are
pluggable in both 3-volt and 5-volt hosts.
Atmel’s AT27BV010 has additional features to ensure high
quality and efficient production use. The Rapid Program-
ming Algorithm reduces the time required to program the
part and guarantees reliable programming. Programming
time is typically only 100
μ
s/byte. The Integrated Product
Identification Code electronically identifies the device and
manufacturer. This feature is used by industry standard
programming equipment to select the proper programming
algorithms and voltages. The AT27BV010 programs
exactly the same way as a standard 5V AT27C010 and
uses the same programming equipment.
System Considerations
Switching between active and standby conditions via the
Chip Enable pin may produce transient voltage excursions.
Unless accommodated by the system design, these tran-
sients may exceed data sheet limits, resulting in device
non-conformance. At a minimum, a 0.1
μ
F high frequency,
low inherent inductance, ceramic capacitor should be uti-
lized for each device. This capacitor should be connected
between the V
CC
and Ground terminals of the device, as
close to the device as possible. Additionally, to stabilize the
supply voltage level on printed circuit boards with large
EPROM arrays, a 4.7
μ
F bulk electrolytic capacitor should
be utilized, again connected between the V
CC
and Ground
terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected
to the array.
Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| AT27BV512-70JC | x8 EPROM |
| AT27BV512-70JI | x8 EPROM |
| AT27BV512-70RC | x8 EPROM |
| AT27BV512-70RI | x8 EPROM |
| AT27C010(L) | AT27C010(L) [Updated 7/98. 16 Pages] 1M bit EPROM. Standard & Low Power |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT27BV040-12JC | 功能描述:IC OTP 4MBIT 120NS 32PLCC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:1M (64K x 16) 速度:150ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT27BV040-12JI | 功能描述:可擦除可编程ROM 4Mb (512Kx8) OTP 2.7-3.6V 120ns RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| AT27BV040-12JU | 功能描述:可擦除可编程ROM 4Mb (512Kx8) OTP 2.7-3.6V 120ns RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| AT27BV040-12LC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 EPROM |
| AT27BV040-12LI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 EPROM |
发布紧急采购，3分钟左右您将得到回复。