- 您现在的位置：买卖IC网 > PDF目录362472 > AT27C010-25PI x8 EPROM PDF资料下载
参数资料
| 型号： | AT27C010-25PI |
| 英文描述： | x8 EPROM |
| 中文描述： | x8存储器 |
| 文件页数： | 2/16页 |
| 文件大小： | 156K |
| 代理商： | AT27C010-25PI |
AT27C010(L)
2
The AT27C010(L) in available in a choice of industry stan-
dard JEDEC-approved one-time programmable (OTP)
plastic PDIP, PLCC, and TSOP packages. All devices fea-
ture two line control (CE, OE) to give designers the flexibil-
ity to prevent bus contention.
With 128K byte storage capability, the AT27C010(L) allows
firmware to be stored reliably and to be accessed by the
system without the delays of mass storage media.
Atmel’s 27C010(L) have additional features to ensure high
quality and efficient production use. The Rapid Program-
ming Algorithm reduces the time required to program the
part and guarantees reliable programming. Programming
time is typically only 100 μs/byte. The Integrated Product
Identification Code electronically identifies the device and
manufacturer. This feature is used by industry standard
programming equipment to select the proper programming
algorithms and voltages.
System Considerations
Switching between active and standby conditions via the
Chip Enable pin may produce transient voltage excursions.
Unless accommodated by the system design, these tran-
sients may exceed data sheet limits, resulting in device
non-conformance. At a minimum, a 0.1
μ
F high frequency,
low inherent inductance, ceramic capacitor should be uti-
lized for each device. This capacitor should be connected
between the V
CC
and Ground terminals of the device, as
close to the device as possible. Additionally, to stabilize the
supply voltage level on printed circuit boards with large
EPROM arrays, a 4.7
μ
F bulk electrolytic capacitor should
be utilized, again connected between the V
CC
and Ground
terminals. This capacitor should be positioned as close as
possible to the point where the power supply is connected
to the array.
Block Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| AT27C010-45DC | x8 EPROM |
| AT27C010-45DI | x8 EPROM |
| AT27C010-45LC | x8 EPROM |
| AT27C010-45LI | x8 EPROM |
| AT27C010-55DC | x8 EPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT27C010-45DC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 EPROM |
| AT27C010-45DI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 EPROM |
| AT27C010-45JC | 功能描述:可擦除可编程ROM 1M bit RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
| AT27C01045JI | 制造商:Atmel Corporation 功能描述: |
| AT27C010-45JI | 功能描述:可擦除可编程ROM 1Mb (128Kx8) OTP 5V 45ns RoHS:否 制造商:Maxim Integrated 类型: 存储容量:1024 bit 组织:1 K x 1 接口类型: 工作电流:5 uA 编程电压: 工作电源电压:2.8 V to 6 V 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:TO-92 |
发布紧急采购，3分钟左右您将得到回复。