- 您现在的位置：买卖IC网 > PDF目录12036 > AT32UC3L064-ZAUT (Atmel)MCU AVR32 64KB FLASH 48VQFN PDF资料下载
参数资料
| 型号： | AT32UC3L064-ZAUT |
| 厂商： | Atmel |
| 文件页数： | 157/174页 |
| 文件大小： | 0K |
| 描述： | MCU AVR32 64KB FLASH 48VQFN |
| 产品培训模块： | MCU Product Line Introduction AVR® UC3 Introduction |
| 标准包装： | 2,080 |
| 系列： | AVR®32 UC3 L |
| 核心处理器： | AVR |
| 芯体尺寸： | 32-位 |
| 速度： | 50MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 36 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 16K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.62 V ~ 3.6 V |
| 数据转换器： | A/D 9x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 包装： | 托盘 |
| 其它名称： | 32UC3L064-ZAUT 32UC3L064-ZAUT-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页当前第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页
83
32099I–01/2012
AT32UC3L016/32/64
The page buffer is not automatically reset after a page write. The programmer should do this
manually by issuing the Clear Page Buffer flash command. This can be done after a page write,
or before the page buffer is loaded with data to be stored to the flash page.
8.5
Flash Commands
The FLASHCDW offers a command set to manage programming of the flash memory, locking
and unlocking of regions, and full flash erasing. See Section 8.8.2 for a complete list of
commands.
To run a command, the CMD field in the Flash Command Register (FCMD) has to be written
with the command number. As soon as the FCMD register is written, the FRDY bit in the Flash
Status Register (FSR) is automatically cleared. Once the current command is complete, the
FSR.FRDY bit is automatically set. If an interrupt has been enabled by writing a one to
FCR.FRDY, the interrupt request line of the Flash Controller is activated. All flash commands
except for Quick Page Read (QPR) and Quick User Page Read (QPRUP) will generate an inter-
rupt request upon completion if FCR.FRDY is one.
Any HSB bus transfers attempting to read flash memory when the FLASHCDW is busy execut-
ing a flash command will be stalled, and allowed to continue when the flash command is
complete.
After a command has been written to FCMD, the programming algorithm should wait until the
command has been executed before attempting to read instructions or data from the flash or
writing to the page buffer, as the flash will be busy. The waiting can be performed either by poll-
ing the Flash Status Register (FSR) or by waiting for the flash ready interrupt. The command
written to FCMD is initiated on the first clock cycle where the HSB bus interface in FLASHCDW
is IDLE. The user must make sure that the access pattern to the FLASHCDW HSB interface
contains an IDLE cycle so that the command is allowed to start. Make sure that no bus masters
such as DMA controllers are performing endless burst transfers from the flash. Also, make sure
that the CPU does not perform endless burst transfers from flash. This is done by letting the
CPU enter sleep mode after writing to FCMD, or by polling FSR for command completion. This
polling will result in an access pattern with IDLE HSB cycles.
All the commands are protected by the same keyword, which has to be written in the eight high-
est bits of the FCMD register. Writing FCMD with data that does not contain the correct key
and/or with an invalid command has no effect on the flash memory; however, the PROGE bit is
set in the Flash Status Register (FSR). This bit is automatically cleared by a read access to the
FSR register.
Writing a command to FCMD while another command is being executed has no effect on the
flash memory; however, the PROGE bit is set in the Flash Status Register (FSR). This bit is
automatically cleared by a read access to the FSR register.
If the current command writes or erases a page in a locked region, or a page protected by the
BOOTPROT fuses, the command has no effect on the flash memory; however, the LOCKE bit is
set in the FSR register. This bit is automatically cleared by a read access to the FSR register.
8.5.1
Write/Erase Page Operation
Flash technology requires that an erase must be done before programming. The entire flash can
be erased by an Erase All command. Alternatively, pages can be individually erased by the
Erase Page command.
The User page can be written and erased using the mechanisms described in this chapter.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J1Z-IW-F2 | CONVERTER MOD DC/DC 2V 40W |
| VE-B3R-IY-F2 | CONVERTER MOD DC/DC 7.5V 50W |
| VJ1825A223JBBAT4X | CAP CER 0.022UF 100V 5% NP0 1825 |
| VJ1825A223KBBAT4X | CAP CER 0.022UF 100V NP0 1825 |
| VE-J1Y-IY-F4 | CONVERTER MOD DC/DC 3.3V 33W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT32UC3L0-XPLD | 功能描述:开发板和工具包 - AVR UC3 L0 Xplained Eval Kit RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT32UC3L-EK | 功能描述:开发板和工具包 - AVR AVR32 Eval Kit for AT32UC3L Series RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT33 | 制造商:Panasonic Industrial Company 功能描述:KIT |
| AT-33 | 功能描述:扬声器与变频器 PZ 96dB 2500Hz 15Vpp RoHS:否 制造商:PUI Audio 产品:Speakers 类型:Electromagnetic 频率:900 Hz to 12 kHz 声压级:88 dBA 阻抗:8 Ohms 功率额定值:1.2 W 形状:Round 端接类型:Solder Pad 直径:15 mm 长度: 宽度: 深度:4.4 mm 磁体材料:Neodymium Iron Boran (NdFeB) 圆锥体材料:Mylar |
| AT3-3 | 制造商:AIMCO 功能描述:Steel Track 3 Ft Long |
发布紧急采购，3分钟左右您将得到回复。