- 您现在的位置：买卖IC网 > Datasheet目录313 > AT45CS1282-TC (Atmel)IC FLASH 128MBIT 50MHZ 40TSOP Datasheet资料下载
参数资料
| 型号： | AT45CS1282-TC |
| 厂商： | Atmel |
| 文件页数： | 11/33页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 128MBIT 50MHZ 40TSOP |
| 标准包装： | 120 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | DataFLASH |
| 存储容量： | 128M（16,384 页 x 1056 字节） |
| 速度： | 50MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 40-TFSOP（0.724"，18.40mm 宽） |
| 供应商设备封装： | 40-TSOP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
AT45CS1282 [Preliminary]
commands previously mentioned. If this pin and feature are not utilized it is recom-
mended that the WP pin be driven high externally.
RESET: A low state on the reset pin (RESET) will terminate the operation in progress
and reset the internal state machine to an idle state. The device will remain in the reset
condition as long as a low level is present on the RESET pin. Normal operation can
resume once the RESET pin is brought back to a high level.
The device incorporates an internal power-on reset circuit, so there are no restrictions
on the RESET pin during power-on sequences. If this pin and feature are not utilized it is
recommended that the RESET pin be driven high externally.
READY/BUSY: This open drain output pin will be driven low when the device is busy in
an internally self-timed operation. This pin, which is normally in a high state (through
an external pull-up resistor), will be pulled low during programming/erase operations,
compare operations, and page-to-buffer transfers.
The busy status indicates that the Flash memory array and one of the buffers cannot be
accessed; read and write operations to the other buffer can still be performed.
8-BIT PORT SUPPLY VOLTAGE (VCCP AND GNDP): The VCCP and GNDP pins are
used to supply power for the 8-bit input/output pins (I/O7-I/O0). The VCCP and GNDP
pins need to be used if the 8-bit port is to be utilized; however, these pins s hould be
treated as “don’t connects” if the SER/BYTE pin is not connected or if the SER/BYTE pin
is always driven high externally.
Power-on/Reset State
System
Considerations
When power is first applied to the device, or when recovering from a reset condition, the
device will default to Mode 3. In addition, the output pins (SO or I/O7 - I/O0) will be in a
high impedance state, and a high-to-low transition on the CS pin will be required to start
a valid instruction. The mode (Mode 3 or Mode 0) will be automatically selected on every
falling edge of CS by sampling the inactive clock state. After power is applied and V CC is
at the minimum datasheet value, the system should wait 20 ms before an operational
mode is started.
The RapidS serial interface is controlled by the serial clock SCK, serial input SI and chip
select CS pins. The sequential 8-bit Rapid8 is controlled by the clock CLK, 8 I/Os and
chip select CS pins. These signals must rise and fall monotonically and be free from
noise. Excessive noise or ringing on these pins can be misinterpreted as multiple edges
and cause improper operation of the device. The PC board traces must be kept to a
minimum distance or appropriately terminated to ensure proper operation. If necessary,
decoupling capacitors can be added on these pins to provide filtering against noise
glitches.
As system complexity continues to increase, voltage regulation is becoming more
important. A key element of any voltage regulation scheme is its current sourcing capa-
bility. Like all Flash memories, the peak current for DataFlash occur during the
programming and erase operation. The regulator needs to supply this peak current
requirement. An under specified regulator can cause current starvation. Besides
increasing system noise, current starvation during programming or erase can lead to
improper operation and possible data corruption.
11
3447A–DFLSH–2/04
相关PDF资料 |
PDF描述 |
|---|---|
| AT45DB011B-XI | IC FLASH 1MBIT 20MHZ 14TSSOP |
| AT45DB021B-TI | IC FLASH 2MBIT 20MHZ 28TSOP |
| AT45DB041B-TI | IC FLASH 4MBIT 20MHZ 28TSOP |
| AT45DB081B-TI | IC FLASH 8MBIT 20MHZ 28TSOP |
| AT45DB161B-TI | IC FLASH 16MBIT 20MHZ 28TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT45CS1282-TI | 功能描述:IC FLASH 128MBIT 50MHZ 40TSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT45D011 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:1-Megabit 5.0-volt Only Serial DataFlash |
| AT45D011-JC | 功能描述:闪存 1M bit RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| AT45D011-JI | 功能描述:闪存 1M bit RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| AT45D011-SC | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:1-Megabit 5.0-volt Only Serial DataFlash |
发布紧急采购，3分钟左右您将得到回复。