参数资料
型号: AT45DB080-RI
厂商: ATMEL CORP
元件分类: DRAM
英文描述: 8-Megabit 2.7-volt Only Sequential Access Parallel I/O DataFlash
中文描述: 8M X 1 FLASH 2.7V PROM, 180 ns, PDSO28
封装: 0.330 INCH, PLASTIC, SOIC-28
文件页数: 5/18页
文件大小: 158K
代理商: AT45DB080-RI
AT45DB080
5
can be loaded into buffer 2 (or vice versa). See application
note AN-4 (“Using Atmel’s Serial DataFlash”) for more
details.
HARDWARE PAGE WRITE PROTECT:
If the WP pin is
held low, the first 256 pages of the main memory cannot be
reprogrammed. The only way to reprogram the first 256
pages is to first drive the protect pin high and then use the
program commands previously mentioned. The WP pin is
internally pulled high; therefore, in low pin count applica-
tions, connection of the WP pin is not necessary if this pin
and feature will not be utilized. However, it is recom-
mended that the WP pin be driven high externally when-
ever possible.
RESET:
A low state on the reset pin (RESET) will terminate
the operation in progress and reset the internal state
machine to an idle state. The device will remain in the reset
condition as long as a low level is present on the RESET
pin. Normal operation can resume once the RESET pin is
brought back to a high level.
The device incorporates an internal power-on reset circuit,
so there are no restrictions on the RESET pin during
power-on sequences. The RESET pin is also internally
pulled high; therefore, in low pin count applications, con-
nection of the RESET pin is not necessary if this pin and
Absolute Maximum Ratings*
feature will not be utilized. However, it is recommended
that the RESET pin be driven high externally whenever
possible.
READY/BUSY:
This open drain output pin will be driven
low when the device is busy in an internally self-timed oper-
ation. This pin, which is normally in a high state (through an
external pull-up resistor), will be pulled low during program-
ming operations, compare operations, and during page-to-
buffer transfers.
The busy status indicates that the Flash memory array and
one of the buffers cannot be accessed; read and write
operations to the other buffer can still be performed.
Power On/Reset State
When power is first applied to the device, or when recover-
ing from a reset condition, the device will default to the
“Inactive Clock Polarity High” mode. In addition, the output
pins (I/O
7
- I/O
0
) will be in a high impedance state, and a
high to low transition on the CS pin will be required to start
a valid instruction. The Clock Polarity mode will be auto-
matically selected on every falling edge of CS by sampling
the inactive clock state.
Note:
1. After power is applied and V
CC
is at the minimum specified data sheet value, the system should wait 20 ms before an oper-
ational mode is started.
Temperature Under Bias.......................-55
°
C to +125
°
C
*NOTICE:
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
Storage Temperature............................-65
°
C to +150
°
C
All Input Voltages
(including NC Pins)
with Respect to Ground.........................-0.6V to +6.25V
All Output Voltages
with Respect to Ground...................-0.6V to V
CC
+ 0.6V
DC and AC Operating Range
AT45DB081
Operating Temperature (Case)
Com.
0
°
C to 70
°
C
Ind.
-40
°
C to 85
°
C
V
CC
Power Supply
(1)
2.7V to 3.6V
相关PDF资料
PDF描述
AT45DB080-TC 8-Megabit 2.7-volt Only Sequential Access Parallel I/O DataFlash
AT45DB080-TI 8-Megabit 2.7-volt Only Sequential Access Parallel I/O DataFlash
AT45DB081B-CNU 8-megabit 2.5-volt Only or 2.7-volt Only DataFlash
AT45DB081B-CU 8-megabit 2.5-volt Only or 2.7-volt Only DataFlash
AT45DB081B-RU 8-megabit 2.5-volt Only or 2.7-volt Only DataFlash
相关代理商/技术参数
参数描述
AT45DB080-TC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-Megabit 2.7-volt Only Sequential Access Parallel I/O DataFlash
AT45DB080-TI 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-Megabit 2.7-volt Only Sequential Access Parallel I/O DataFlash
AT45DB081 制造商:Adesto Technologies Corporation 功能描述:ROOT PART: DATAFLASH - Bulk
AT45DB081A 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-megabit 2.7-volt Only Serial DataFlash
AT45DB081A-CC 制造商:未知厂家 制造商全称:未知厂家 功能描述:SPI Serial EEPROM