- 您现在的位置：买卖IC网 > PDF目录20428 > AT45DB321C-CC (Atmel)IC FLASH 32MBIT 40MHZ 24CBGA PDF资料下载
参数资料
| 型号： | AT45DB321C-CC |
| 厂商： | Atmel |
| 文件页数： | 5/40页 |
| 文件大小： | 0K |
| 描述： | IC FLASH 32MBIT 40MHZ 24CBGA |
| 标准包装： | 378 |
| 格式 - 存储器： | 闪存 |
| 存储器类型： | DataFLASH |
| 存储容量： | 32M（8192 页 x 528 字节） |
| 速度： | 40MHz |
| 接口： | SPI 3 线串行 |
| 电源电压： | 2.7 V ~ 3.6 V |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 24-TBGA，CSPBGA |
| 供应商设备封装： | 24-CBGA |
| 包装： | 托盘 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
AT45DB321C
5.1.2
5.1.3
5.2
5.2.1
Main Memory Page Read
A main memory page read allows the user to read data directly from any one of the 8192 pages
in the main memory, bypassing both of the data buffers and leaving the contents of the buffers
unchanged. To start a page read, an opcode of D2H must be clocked into the device. The
opcode is followed by three address bytes (which comprise 24-bit page and byte address
sequence) and 32 don’t care clock cycles. The first bit of the 24-bit address sequence is a
reserved bit, the next 13 bits (PA12-PA0) of the 24-bit address sequence specify the page in
main memory to be read, and the last 10 bits (BA9-BA0) of the 24-bit address sequence specify
the starting byte address within that page. The 32 don’t care clock cycles that follow the three
address bytes are sent to initialize the read operation. Following the don’t care bytes, additional
pulses on SCK result in data being output on the SO (serial output) pin. The CS pin must remain
low during the loading of the opcode, the address bytes, the don’t care bytes, and the reading of
data. When the end of a page in main memory is reached, the device will continue reading back
at the beginning of the same page. A low-to-high transition on the CS pin will terminate the read
operation and tristate the output pin (SO). The maximum SCK frequency allowable for the Main
Memory Page Read is defined by the f SCK specification. The Main Memory Page Read bypasses
both data buffers and leaves the contents of the buffers unchanged.
Buffer Read
Data can be read from either one of the two buffers, using different opcodes to specify which
buffer to read from. An opcode of D4H is used to read data from buffer 1, and an opcode of D6H
is used to read data from buffer 2. To perform a buffer read, the opcode must be clocked into the
device followed by three address bytes comprised of 14 don’t care bits and 10 buffer address
bits (BFA9-BFA0). Following the three address bytes, an additional don’t care byte must be
clocked in to initialize the read operation. Since the buffer size is 528 bytes, 10 buffer address
bits are required to specify the first byte of data to be read from the buffer. The CS pin must
remain low during the loading of the opcode, the address bytes, the don’t care bytes, and the
reading of data. When the end of a buffer is reached, the device will continue reading back at the
beginning of the buffer. A low-to-high transition on the CS pin will terminate the read operation
and tristate the output pin (SO).
Program and Erase Commands
Buffer Write
Data can be clocked in from the SI pin into either buffer 1 or buffer 2. To load data into either
buffer, a 1-byte opcode, 84H for buffer 1 or 87H for buffer 2, must be clocked into the device, fol-
lowed by three address bytes comprised of 14 don’t care bits and 10 buffer address bits (BFA9-
BFA0). The 10 buffer address bits specify the first byte in the buffer to be written. After the last
address byte has been clocked into the device, data can then be clocked in on subsequent clock
cycles. If the end of the data buffer is reached, the device will wrap around back to the beginning
of the buffer. Data will continue to be loaded into the buffer until a low-to-high transition is
detected on the CS pin.
5
3387M–DFLASH–2/08
相关PDF资料 |
PDF描述 |
|---|---|
| R0.25D10-053.3 | CONV DC/DC 0.25W 5VIN +/-3.3VOUT |
| 17PY-Z858-99VS | MOTOR STEP UNI 42MM SQ 24V DL |
| 1487D48 | WIREWAY PULL THRGH 48" 6X6" GREY |
| EBA15DRMH | CONN EDGECARD 30POS .125 SQ WW |
| ESA06DTMH | CONN EDGECARD 12POS R/A .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT45DB321C-CI | 功能描述:IC FLASH 32MBIT 40MHZ 24CBGA RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:RAM 存储器类型:SDRAM 存储容量:256M（8Mx32） 速度:143MHz 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:90-VFBGA 供应商设备封装:90-VFBGA（8x13） 包装:托盘 其它名称:Q2841869 |
| AT45DB321C-CNC | 功能描述:IC FLASH 32MBIT 40MHZ 8CASON RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:RAM 存储器类型:SDRAM 存储容量:256M（8Mx32） 速度:143MHz 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:90-VFBGA 供应商设备封装:90-VFBGA（8x13） 包装:托盘 其它名称:Q2841869 |
| AT45DB321C-CNU | 功能描述:IC FLASH 32MBIT 40MHZ 8CASON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:RAM 存储器类型:SDRAM 存储容量:256M（8Mx32） 速度:143MHz 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:90-VFBGA 供应商设备封装:90-VFBGA（8x13） 包装:托盘 其它名称:Q2841869 |
| AT45DB321C-CU | 功能描述:IC FLASH 32MBIT 40MHZ 24CBGA RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:RAM 存储器类型:SDRAM 存储容量:256M（8Mx32） 速度:143MHz 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:90-VFBGA 供应商设备封装:90-VFBGA（8x13） 包装:托盘 其它名称:Q2841869 |
| AT45DB321-CI | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-Megabit 2.7-volt Only Serial DataFlash |
发布紧急采购，3分钟左右您将得到回复。