- 您现在的位置：买卖IC网 > PDF目录381460 > AT49LV080T (Atmel Corp.) 8-Megabit Single 2.7-volt Battery-Voltage Flash Memory(8M位单电源2.7V Battery-Voltage技术闪速存储器) PDF资料下载
参数资料
| 型号： | AT49LV080T |
| 厂商： | Atmel Corp. |
| 英文描述： | 8-Megabit Single 2.7-volt Battery-Voltage Flash Memory(8M位单电源2.7V Battery-Voltage技术闪速存储器) |
| 中文描述： | 8兆位单2.7伏电池电压快闪记忆体（800万位单电源为2.7V电池电压技术闪速存储器） |
| 文件页数： | 3/16页 |
| 文件大小： | 173K |
| 代理商： | AT49LV080T |
AT49BV/LV080(T)
3
the system. Enabling the lockout feature will allow the boot
code to stay in the device while data in the rest of the
device is updated. This feature does not have to be acti-
vated; the boot block’s usage as a write protected region is
optional to the user. The address range of the
AT49BV/LV080 boot block is 00000H to 03FFFH while the
address range of the AT49BV/LV080T boot block is
FC000H to FFFFFH.
To activate the lockout feature, a series of six program
commands to specific addresses with specific data must be
performed. Please refer to the Command Definitions table.
BOOT BLOCK LOCKOUT DETECTION:
A software
method is available to determine if programming of the boot
block section is locked out. When the device is in the soft-
ware product identification mode (see Software Product
Identification Entry and Exit sections) a read from address
location 00002H will show if programming the boot block is
locked out for the AT49BV/LV080, and a read from address
location FC002H will show if programming the boot block is
locked out for the AT49BV/LV080T. If the data on I/O0 is
low, the boot block can be programmed; if the data on I/O0
is high, the program lockout feature has been activated and
the block cannot be programmed. The software product
identification exit code should be used to return to standard
operation.
BOOT BLOCK PROGRAMMING LOCKOUT OVERRIDE:
The user can override the boot block programming lockout
by taking the RESET pin to 12 + 0.5 volts. By doing this,
protected boot block data can be altered through a chip
erase, or byte programming. When the RESET pin is
brought back to TTL levels the boot block programming
lockout feature is again active.
PRODUCT IDENTIFICATION:
The product identification
mode identifies the device and manufacturer as Atmel. It
may be accessed by hardware or software operation. The
hardware operation mode can be used by an external pro-
grammer to identify the correct programming algorithm for
the Atmel product.
For details, see Operating Modes (for hardware operation)
or Software Product Identification. The manufacturer and
device code is the same for both modes.
DATA POLLING:
The AT49BV/LV080(T) features DATA
polling to indicate the end of a program cycle. During a pro-
gram cycle an attempted read of the last byte loaded will
result in the complement of the loaded data on I/O7. Once
the program cycle has been completed, true data is valid
on all outputs and the next cycle may begin. DATA polling
may begin at any time during the program cycle.
TOGGLE BIT:
In addition to DATA polling, the
AT49BV/LV080 provides another method for determining
the end of a program or erase cycle. During a program or
erase operation, successive attempts to read data from the
device will result in I/O6 toggling between one and zero.
Once the program cycle has completed, I/O6 will stop tog-
gling and valid data will be read. Examining the toggle bit
may begin at any time during a program cycle.
RDY/BUSY:
An open drain READY/BUSY output pin pro-
vides another method of detecting the end of a program or
erase operation. RDY/BUSY is actively pulled low during
the internal program and erase cycles and is released at
the completion of the cycle. The open drain connection
allows for OR - tying of several devices to the same
RDY/BUSY line.
RESET:
A RESET input pin is provided to ease some sys-
tem applications. When RESET is at a logic high level, the
device is in its standard operating mode. A low level on the
RESET input halts the present device operation and puts
the outputs of the device in a high impedance state. If the
RESET pin makes a high to low transition during a program
or erase operation, the operation may not be successfully
completed, and the operation will have to be repeated after
a high level is applied to the RESET pin. When a high level
is reasserted on the RESET pin, the device returns to the
read or standby mode, depending upon the state of the
control inputs. By applying a 12V + 0.5V input signal to the
RESET pin the boot block array can be reprogrammed
even if the boot block lockout feature has been enabled
(see Boot Block Programming Lockout Override section).
HARDWARE DATA PROTECTION:
Hardware features
protect against inadvertent programs to the
AT49BV/LV080(T) in the following ways: (a) V
CC
sense–if
V
CC
is below 1.8V (typical), the program function is inhib-
ited; (b) Program inhibit—holding any one of OE low, CE
high or WE high inhibits program cycles; and (c) Noise fil-
ter—pulses of less than 15 ns (typical) on the WE or CE
inputs will not initiate a program cycle.
相关PDF资料 |
PDF描述 |
|---|---|
| AT49BV1024A | 1-megabit (64K x 16) 3-volt Only Flash Memory |
| AT49LV1024A | 1-megabit (64K x 16) 3-volt Only Flash Memory |
| AT49LV1024A-45VC | 1-megabit (64K x 16) 3-volt Only Flash Memory |
| AT49LV1024A-45VL | 1-megabit (64K x 16) 3-volt Only Flash Memory |
| AT49BV1604T-90TC | 16-Megabit 1M x 16/2M x 8 3-volt Only Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT49LV102470VC | 制造商:ATMEL 功能描述:IC FLASH MEMORY 1M 3V 40-VSOP |
| AT49LV1024-70VC | 功能描述:IC FLASH 1MBIT 70NS 40VSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT49LV1024-90JC | 功能描述:IC FLASH 1MBIT 90NS 44PLCC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT49LV1024-90VC | 功能描述:IC FLASH 1MBIT 90NS 40VSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT49LV1024-90VI | 功能描述:IC FLASH 1MBIT 90NS 40VSOP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。