- 您现在的位置：买卖IC网 > PDF目录11214 > AT80C51RD2-3CSUM (Atmel)IC 8051 MCU 5V SPI 20MHZ 40-DIP PDF资料下载
参数资料
| 型号： | AT80C51RD2-3CSUM |
| 厂商： | Atmel |
| 文件页数： | 52/81页 |
| 文件大小： | 0K |
| 描述： | IC 8051 MCU 5V SPI 20MHZ 40-DIP |
| 标准包装： | 216 |
| 系列： | 80C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 40MHz |
| 连通性： | UART/USART |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器类型： | ROMless |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页
56
4113D–8051–01/09
AT80C51RD2
14. Power Management
14.1
Idle Mode
An instruction that sets PCON.0 indicates that it is the last instruction to be executed before
going into Idle mode. In Idle mode, the internal clock signal is gated off to the CPU, but not to the
interrupt, Timer, and Serial Port functions. The CPU status is preserved in its entirety: the Stack
Pointer, Program Counter, Program Status Word, Accumulator and all other registers maintain
their data during idle. The port pins hold the logical states they had at the time Idle was acti-
vated. ALE and PSEN hold at logic high level.
There are two ways to terminate the Idle mode. Activation of any enabled interrupt will cause
PCON.0 to be cleared by hardware, terminating the Idle mode. The interrupt will be serviced,
and following RETI the next instruction to be executed will be the one following the instruction
that put the device into idle.
The flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred during nor-
mal operation or during idle. For example, an instruction that activates idle can also set one or
both flag bits. When idle is terminated by an interrupt, the interrupt service routine can examine
the flag bits.
The other way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is
still running, the hardware reset needs to be held active for only two machine cycles (24 oscilla-
tor periods) to complete the reset.
14.2
Power-down Mode
To save maximum power, a power-down mode can be invoked by software (refer to Table 11-
12, PCON register).
In power-down mode, the oscillator is stopped and the instruction that invoked power-down
mode is the last instruction executed. The internal RAM and SFRs retain their value until the
power-down mode is terminated. V
CC can be lowered to save further power. Either a hardware
reset or an external interrupt can cause an exit from power-down. To properly terminate power-
down, the reset or external interrupt should not be executed before V
CC is restored to its normal
operating level and must be held active long enough for the oscillator to restart and stabilize.
Only external interrupts INT0, INT1 and Keyboard Interrupts are useful to exit from power-down.
Thus, the interrupt must be enabled and configured as level - or edge - sensitive interrupt input.
When Keyboard Interrupt occurs after a power-down mode, 1024 clocks are necessary to exit to
power-down mode and enter in operating mode.
Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed
in Figure 14-1. When both interrupts are enabled, the oscillator restarts as soon as one of the
two inputs is held low and power-down exit will be completed when the first input is released. In
this case, the higher priority interrupt service routine is executed. Once the interrupt is serviced,
the next instruction to be executed after RETI will be the one following the instruction that put
AT80C51RD2 into power-down mode.
相关PDF资料 |
PDF描述 |
|---|---|
| ADG406BPZ-REEL | IC MULTIPLEXER 16X1 28PLCC |
| VE-JWN-IW | CONVERTER MOD DC/DC 18.5V 100W |
| VE-JWM-IW | CONVERTER MOD DC/DC 10V 100W |
| VE-B3V-IX-F2 | CONVERTER MOD DC/DC 5.8V 75W |
| VE-JWL-IW | CONVERTER MOD DC/DC 28V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT80C51RD2-RLRUM | 功能描述:8位微控制器 -MCU MCU 8-Bit HI Perform ROMless 3-5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT80C51RD2-RLTIL | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:80C51 High Performance ROM 8-bit Microcontroller |
| AT80C51RD2-RLTIM | 功能描述:IC MCU 8051 5V SPI 20MHZ 44-VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:80C 标准包装:9 系列:87C 核心处理器:8051 芯体尺寸:8-位 速度:40/20MHz 连通性:UART/USART 外围设备:POR，WDT 输入/输出数:32 程序存储器容量:32KB（32K x 8） 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:0°C ~ 70°C 封装/外壳:40-DIP（0.600"，15.24mm） 包装:管件 |
| AT80C51RD2-RLTUL | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:80C51 High Performance ROM 8-bit Microcontroller |
| AT80C51RD2-RLTUM | 功能描述:8位微控制器 -MCU MCU 8-Bit HI Perform ROMless 3-5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。