- 您现在的位置：买卖IC网 > PDF目录381497 > AT86RF230-ZU (ATMEL CORP) ZigBee/IEEE 802.15.4-Transceiver PDF资料下载
参数资料
| 型号： | AT86RF230-ZU |
| 厂商： | ATMEL CORP |
| 元件分类： | 网络接口 |
| 英文描述： | ZigBee/IEEE 802.15.4-Transceiver |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, PQCC32 |
| 封装： | 5 X 5 MM, 0.50 MM PITCH, GREEN, PLASTIC, MO-220VHHD-6, QFN-32 |
| 文件页数： | 20/50页 |
| 文件大小： | 445K |
| 代理商： | AT86RF230-ZU |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
20
AT86RF230
5131A-ZIGB-06/14/06
6. Functional Description
6.1. RSSI/Energy Detection
The internal limiter amplifier provides an RSSI value which reflects the current receive signal strength at the
antenna pin of the AT86RF230. The RSSI is a 5-bit value indicating the receive power in steps of 3 dB (see register
0x06), and is updated every 2
μ
s.
The receiver ED measurement is used with the channel-scan algorithm. An ED request (write access to register
0x07) as defined by the IEEE 802.15.4 standard has a measurement time of 128
μ
s. The ED measurement result
is accessible after the measurement time at register 0x07 (PHY_ED_LEVEL). With every frame reception (SFD
detection), an ED measurement is automatically started. The ED measurement result has the same range as the
RSSI value (register 0x06), but with a 1 dB resolution.
6.2. Link Quality Indication
The IEEE 802.15.4 standard defines the link quality indication (LQI) measurement as a “characterization of the
strength and/or quality of a received packet”. The LQI measurement of the AT86RF230 is implemented as a
characterization of both the quality and signal strength. An average correlation value of multiple symbols is
calculated and appended to each frame after scaling to a value ranging from 0 to 255. The minimum LQI value of 0
is associated with a low signal quality, resulting from high signal distortions, and/or a signal strength that is below
the receiver sensitivity. The maximum value of 255 is associated with a signal strength higher than the receiver
sensitivity and a high signal quality resulting from low signal distortions. Signal distortions are mainly generated by
interference and multipath propagation.
6.3. Clear Channel Assessment
The IEEE 802.15.4 standard defines three clear channel assessment (CCA) modes:
Mode 1: energy above threshold only
Mode 2: carrier sense only
Mode 3: carrier sense with energy above threshold
All three modes are available in AT86RF230. The modes are configurable via register 0x08 (PHY_CC_CCA). A
CCA request is initiated by writing to bit 7 in register 0x08 (PHY_CC_CCA). After the CCA evaluation time of
128
μ
s, the CCA result is accessible at register 0x01 (TRX_STATUS) bits 6 and 7. Bit 7 indicates whether the CCA
measurement is finished or not, bit 6 indicates a busy (bit 6 = 0) or clear channel. (bit 6 = 1)
The CCA modes are further configurable using register 0x09 (CCA_THRES).
The 4-bit value CCA_CS_THRES can be used for fine tuning the sensitivity of the CCA carrier sense algorithm.
Higher values increase the probability of clear channel detection.
The other 4-bit value (CCA_ED_THRES) of register 0x09 (CCA_THRES) defines the received power threshold of
the “energy above threshold” algorithm. Any received power above this level will indicate a busy channel. The
threshold is calculated by -91+2·CCA_ED_THRES [dBm], resulting in a range of -91 dBm to -61 dBm.
6.4. Voltage Regulators
Two identical low-dropout voltage regulators are integrated within the AT86RF230. The AVREG provides the
regulated 1.8V supply voltage for the analog section and the DVREG supplies the low-voltage digital section. A
simplified schematic is shown in
Figure 6-1
. The voltage regulators are connected internally to the external
unregulated supply voltage VDD. The regulated output voltage is available on pin VDEC1 or VDEC2. External
decoupling capacitors should be connected to these pins to stabilize the regulated supply voltage. A decoupling
capacitor value of 1
μ
F is recommended for stable operation of the voltage regulators (see chapter 9), but it can
相关PDF资料 |
PDF描述 |
|---|---|
| AT86RF401E | Smart RF Wireless Data Microtransmitter |
| AT86RF401U | Smart RF Wireless Data Microtransmitter |
| AT86RF401X | Smart RF Wireless Data Microtransmitter |
| AT86RF535A | WiMax Transceiver 802.16-2004 |
| AT86RF535B | 3.5GHz WiMAX Transceiver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT86RF230-ZU SL176 | 制造商:Atmel Corporation 功能描述: |
| AT86RF230-ZUR | 功能描述:射频收发器 2.4 GHZ ZigBee Transceiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| AT86RF231 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Low power 2.4 GHz Transceiver for ZigBee, IEEE 802.15.4, and ISM Applications |
| AT86RF231-ZF | 功能描述:射频收发器 2.4GHZ ZigBee Transceiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
| AT86RF231-ZFR | 功能描述:射频收发器 2.4GHZ ZigBee Transceiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。