收藏本站
参数资料
型号： AT89C51ED2-SMSUM
厂商： Atmel
文件页数： 118/137页
文件大小： 0K
描述： IC 8051 MCU FLASH 64K 68PLCC
产品培训模块： MCU Product Line Introduction
标准包装： 304
系列： 89C
核心处理器： 8051
芯体尺寸： 8-位
速度： 60MHz
连通性： SPI，UART/USART
外围设备： POR，PWM，WDT
输入/输出数： 50
程序存储器容量： 64KB（64K x 8）
程序存储器类型： 闪存
EEPROM 大小： 2K x 8
RAM 容量： 2K x 8
电压 - 电源 (Vcc/Vdd)： 2.7 V ~ 5.5 V
振荡器型： 外部
工作温度： -40°C ~ 85°C
封装/外壳： 68-PLCC
包装： 管件
配用： AT89OCD-01-ND - USB EMULATOR FOR AT8XC51 MCU
81
4235K–8051–05/08
AT89C51RD2/ED2
18.3
Power-Down Mode
The Power-Down mode places the AT89C51RD2/ED2 in a very low power state. Power-Down
mode stops the oscillator, freezes all clock at known states. The CPU status prior to entering
Power-Down mode is preserved, i.e., the program counter, program status word register retain
their data for the duration of Power-Down mode. In addition, the SFR and RAM contents are pre-
served. The status of the Port pins during Power-Down mode is detailed in Table 18-1.
Note:
VCC may be reduced to as low as VRET during Power-Down mode to further reduce power dissi-
pation. Take care, however, that VDD is not reduced until Power-Down mode is invoked.
18.3.1
Entering Power-Down Mode
To enter Power-Down mode, set PD bit in PCON register. The AT89C51RD2/ED2 enters the
Power-Down mode upon execution of the instruction that sets PD bit. The instruction that sets
PD bit is the last instruction executed.
18.3.2
Exiting Power-Down Mode
Note:
If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until VCC is
restored to the normal operating level.
There are three ways to exit the Power-Down mode:
1.
Generate an enabled external interrupt.
– The AT89C51RD2/ED2 provides capability to exit from Power-Down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and restores the
clocks to the CPU and peripherals. Using INTx# input, execution resumes when the
input is released (see Figure 18-1). Execution resumes with the interrupt service
routine. Upon completion of the interrupt service routine, program execution
resumes with the instruction immediately following the instruction that activated
Power-Down mode.
Note:
The external interrupt used to exit Power-Down mode must be configured as level sensitive
(INT0# and INT1#) and must be assigned the highest priority. In addition, the duration of the inter-
rupt must be long enough to allow the oscillator to stabilize. The execution will only resume when
the interrupt is deasserted.
Note:
Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM content.
Figure 18-1. Power-Down Exit Waveform Using INT1:0#
2.
Generate a reset.
– A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU and
peripherals. Program execution momentarily resumes with the instruction
immediately following the instruction that activated Power-Down mode and may
INT1:0#
OSC
Power-down phase
Oscillator restart phase
Active phase
相关PDF资料
PDF描述
AT89C51ED2-RDTUM IC 8051 MCU FLASH 64K 64VQFP
PX0852 COVER FOR USB FLASHDRIVE SEALED
VJ2225A271JBLAT4X CAP CER 270PF 630V 5% NP0 2225
AT32UC3C1128C-AUT IC MCU AVR32 128K FLASH 100TQFP
DF36012FPV IC H8 MCU FLASH 16K 64LQFP
相关代理商/技术参数
参数描述
AT89C51ED2-UM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51IC2 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller with 2-wire Interface
AT89C51IC2_04 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller with 2-wire Interface
AT89C51IC2_08 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller with 2-wire Interface
AT89C51IC2-RLRIL 功能描述:IC MCU FLASH 8051 32K 3V 44-VQFP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 标准包装:1 系列:AVR® ATmega 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，SPI，UART/USART 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:32 程序存储器容量:32KB（16K x 16） 程序存储器类型:闪存 EEPROM 大小:1K x 8 RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:44-TQFP 包装:剪切带 (CT) 其它名称:ATMEGA324P-B15AZCT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*