参数资料
型号: AT89C51RE2-SLRUM
厂商: Atmel
文件页数: 124/187页
文件大小: 0K
描述: MCU 8051 128K FLASH 44-PLCC
产品培训模块: MCU Product Line Introduction
标准包装: 1
系列: 89C
核心处理器: 8051
芯体尺寸: 8-位
速度: 60MHz
连通性: I²C,SPI,UART/USART
外围设备: POR,PWM,WDT
输入/输出数: 34
程序存储器容量: 128KB(128K x 8)
程序存储器类型: 闪存
RAM 容量: 8K x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
振荡器型: 外部
工作温度: -40°C ~ 85°C
封装/外壳: 44-LCC(J 形引线)
包装: 标准包装
其它名称: AT89C51RE2-SLRUMDKR
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页当前第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页
41
7663E–8051–10/08
AT89C51RE2
Loading the Column
Latches
Any number of data from 0 byte to 128 bytes can be loaded in the column latches. The data writ-
ten in the column latches can be written in a none consecutive order. The DPTR allows to select
the address of the byte to load in the column latches.
The page address to be written (target page in FM0) is given by the last address loaded in the
column latches and when this page belongs to the upper 32K bytes of the logical addressable
MCU space, the target memory bank selection is performed upon the MBO2:0 value during the
last address loaded.
When 0 byte is loaded in the column latches the activation sequence (5xh, Axh in FCON) does
not launch any operations. The FSE bit in FSTA register is set.
When a current flash write operation is on-going (FBUSY is set), it is impossible to load the col-
umns latches before the end of flash programming process (the write operation in the columns
latches is not performed, and the previous columns latches content is not overwritten).
When programming is launched, an automatic erase of the entire memory page is first per-
formed, then programming is effectively done. Thus no page or block erase is needed and only
the loaded data are programmed in the corresponding page. The unloaded data of the target
memory page are programmed at 0xFF value (automatic page erase value).
The following procedure is used to load the column latches and is summarized in Figure 13:
Disable interrupt and map the column latch space by setting FPS bit.
Select the target memory bank (for page address larger than 32K)
Map the column latch
Reset the column latch
Load the DPTR with the address to write.
Load Accumulator register with the data to write.
Execute the MOVX @DPTR, A instruction, and only this one (no MOVX @Ri, A).
If needed loop the last three instructions until the page is completely loaded.
Unmap the column latch if needed (it can be left mapped) and Enable Interrupt
相关PDF资料
PDF描述
AT89C51SND1C-7HTUL IC MCU 64KB FLASH MEM 81-CBGA
AT89C51SND2C-7FTUL IC 8051 MCU FLASH 64K MP3 100BGA
AT89C52-24PI IC MICRO CTRL 24MHZ 40DIP
AT89C55WD-24AU IC 8051 MCU FLASH 20K 44TQFP
AT89EB5114-TGSIL IC 8051 MCU FLASH 4K 20SOIC
相关代理商/技术参数
参数描述
AT89C51RE2-SLSEM 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Flash Microcontroller
AT89C51RE2-SLSUM 功能描述:8位微控制器 -MCU C51RE2 128k FLASH 2.7V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT89C51SND1 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:MP3 Microcontrollers
AT89C51SND1_06 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:USB Microcontrollers
AT89C51SND1A-ROTIL 制造商:未知厂家 制造商全称:未知厂家 功能描述:MICROCONTROLLER|8-BIT|8051 CPU|CMOS|QFP|80PIN|PLASTIC