- 您现在的位置：买卖IC网 > PDF目录381504 > AT89C52-12JI (ATMEL CORP) RY Series - Econoline Regulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 24V; Power: 1W; On/Off Pin; 1kVDC Isolation; UL94V-0 Package Material; Optional Continuous Short Circuit Protected; Internal linear regulator; Efficiency to 70% PDF资料下载
参数资料
| 型号： | AT89C52-12JI |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | RY Series - Econoline Regulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 24V; Power: 1W; On/Off Pin; 1kVDC Isolation; UL94V-0 Package Material; Optional Continuous Short Circuit Protected; Internal linear regulator; Efficiency to 70% |
| 中文描述： | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQCC44 |
| 封装： | PLASTIC, MS-018AC, LCC-44 |
| 文件页数： | 3/22页 |
| 文件大小： | 181K |
| 代理商： | AT89C52-12JI |
AT89C52
4-63
The AT89C52 provides the following standard features: 8K
bytes of Flash, 256 bytes of RAM, 32 I/O lines, three 16-bit
timer/counters, a six-vector two-level interrupt architecture,
a full duplex serial port, on-chip oscillator, and clock cir-
cuitry. In addition, the AT89C52 is designed with static logic
for operation down to zero frequency and supports two
software selectable power saving modes. The Idle Mode
stops the CPU while allowing the RAM, timer/counters,
serial port, and interrupt system to continue functioning.
The Power Down Mode saves the RAM contents but
freezes the oscillator, disabling all other chip functions until
the next hardware reset.
Pin Description
V
CC
Supply voltage.
GND
Ground.
Port 0
Port 0 is an 8-bit open drain bidirectional I/O port. As an
output port, each pin can sink eight TTL inputs. When 1s
are written to port 0 pins, the pins can be used as high-
impedance inputs.
Port 0 can also be configured to be the multiplexed low-
order address/data bus during accesses to external pro-
gram and data memory. In this mode, P0 has internal pul-
lups.
Port 0 also receives the code bytes during Flash program-
ming and outputs the code bytes during program verifica-
tion. External pullups are required during program verifica-
tion.
Port 1
Port 1 is an 8-bit bidirectional I/O port with internal pullups.
The Port 1 output buffers can sink/source four TTL inputs.
When 1s are written to Port 1 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 1 pins that are externally being pulled low will source
current (I
IL
) because of the internal pullups.
In addition, P1.0 and P1.1 can be configured to be the
timer/counter 2 external count input (P1.0/T2) and the
timer/counter 2 trigger input (P1.1/T2EX), respectively, as
shown in the following table.
Port 1 also receives the low-order address bytes during
Flash programming and verification.
Port 2
Port 2 is an 8-bit bidirectional I/O port with internal pullups.
The Port 2 output buffers can sink/source four TTL inputs.
When 1s are written to Port 2 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 2 pins that are externally being pulled low will source
current (I
IL
) because of the internal pullups.
Port 2 emits the high-order address byte during fetches
from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @
DPTR). In this application, Port 2 uses strong internal pul-
lups when emitting 1s. During accesses to external data
memory that use 8-bit addresses (MOVX @ RI), Port 2
emits the contents of the P2 Special Function Register.
Port 2 also receives the high-order address bits and some
control signals during Flash programming and verification.
Port 3
Port 3 is an 8-bit bidirectional I/O port with internal pullups.
The Port 3 output buffers can sink/source four TTL inputs.
When 1s are written to Port 3 pins, they are pulled high by
the internal pullups and can be used as inputs. As inputs,
Port 3 pins that are externally being pulled low will source
current (I
IL
) because of the pullups.
Port 3 also serves the functions of various special features
of the AT89C51, as shown in the following table.
Port 3 also receives some control signals for Flash pro-
gramming and verification.
RST
Reset input. A high on this pin for two machine cycles while
the oscillator is running resets the device.
ALE/PROG
Address Latch Enable is an output pulse for latching the
low byte of the address during accesses to external mem-
ory. This pin is also the program pulse input (PROG) during
Flash programming.
In normal operation, ALE is emitted at a constant rate of 1/6
the oscillator frequency and may be used for external tim-
ing or clocking purposes. Note, however, that one ALE
Port Pin
Alternate Functions
P1.0
T2 (external count input to Timer/Counter 2),
clock-out
P1.1
T2EX (Timer/Counter 2 capture/reload trigger
and direction control)
Port Pin
Alternate Functions
P3.0
RXD (serial input port)
P3.1
TXD (serial output port)
P3.2
INT0 (external interrupt 0)
P3.3
INT1 (external interrupt 1)
P3.4
T0 (timer 0 external input)
P3.5
T1 (timer 1 external input)
P3.6
WR (external data memory write strobe)
P3.7
RD (external data memory read strobe)
相关PDF资料 |
PDF描述 |
|---|---|
| AT89C52-12PA | 8-Bit Microcontroller with 8K Bytes Flash |
| AT89C52-12PC | RY Series - Econoline Regulated DC-DC Converters; Input Voltage (Vdc): 15V; Output Voltage (Vdc): 24V; Power: 1W; On/Off Pin; 1kVDC Isolation; UL94V-0 Package Material; Optional Continuous Short Circuit Protected; Internal linear regulator; Efficiency to 70% |
| AT89C52-12PI | 8-Bit Microcontroller with 8K Bytes Flash |
| AT89C52 | Hex Inverter 14-SO -40 to 125 |
| AT89C52-12QC | Hex Inverter 14-SO -40 to 85 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT89C52-12LM | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| AT89C52-12LM/883 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
| AT89C52-12PA | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-Bit Microcontroller with 8K Bytes Flash |
| AT89C52-12PC | 功能描述:8位微控制器 -MCU 80C31 w/8k RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89C52-12PI | 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。