- 您现在的位置：买卖IC网 > PDF目录381506 > AT89LV51-12JC (ATMEL CORP) High Speed CMOS Logic Hex Inverters 14-PDIP -55 to 125 PDF资料下载
参数资料
| 型号： | AT89LV51-12JC |
| 厂商： | ATMEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | High Speed CMOS Logic Hex Inverters 14-PDIP -55 to 125 |
| 中文描述： | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQCC44 |
| 封装： | PLASTIC, LCC-44 |
| 文件页数： | 6/16页 |
| 文件大小： | 197K |
| 代理商： | AT89LV51-12JC |
AT89LV51
4-50
Program Memory Lock Bits
On the chip are three lock bits which can be left unpro-
grammed (U) or can be programmed (P) to obtain the addi-
tional features listed in the table below:
Lock Bit Protection Modes
(1)
Note:
1. The lock bits can only be erased with the Chip Erase
operation.
When lock bit 1 is programmed, the logic level at the EA pin
is sampled and latched during reset. If the device is pow-
ered up without a reset, the latch initializes to a random
value, and holds that value until reset is activated. It is nec-
essary that the latched value of EA be in agreement with
the current logic level at that pin in order for the device to
function properly.
Programming the Flash
The AT89LV51 is normally shipped with the on-chip Flash
memory array in the erased state (i.e. contents=FFH) and
ready to be programmed.
The respective top-side marking and device signature
codes are listed below:
The AT89LV51 code memory array is programmed byte-
by-byte. To program any non-blank byte in the on-chip
Flash Code Memory, the entire memory must be erased
using the Chip Erase Mode.
Programming Algorithm:
Before programming the
AT89LV51, the address, data and control signals should be
set up according to the Flash programming mode table and
Figure 3 and Figure 4. To program the AT89LV51, the fol-
lowing sequence should be followed:
1.
Input the desired memory location on the address
lines.
2.
Input the appropriate data byte on the data lines.
3.
Activate the correct combination of control signals.
4.
Raise EA/V
PP
to 12V.
5.
Pulse ALE/PROG once to program a byte in the Flash
array or the lock bits. The byte-write cycle is self-timed
and typically takes no more than 1.5 ms. Repeat steps
1 through 5 changing the address and data for the
entire array or until the end of the object file is reached.
Data Polling:
The AT89LV51 features Data Polling to indi-
cate the end of a write cycle. During a write cycle, an
attempted read of the last byte written will result in the com-
plement of the written data on PO.7. Once the write cycle
has been completed, true data is valid on all outputs, and
the next cycle may begin. Data Polling may begin any time
after a write cycle has been initiated.
Ready/Busy:
The progress of byte programming can also
be monitored by the RDY/BSY output signal. P3.4 is pulled
low after ALE goes high during programming to indicate
BUSY. P3.4 is pulled high again when programming is
done to indicate READY.
Program Verify:
If lock bits LB1 and LB2 have not been
programmed, the programmed code data can be read back
via the address and data lines for verification. The lock bits
cannot be verified directly. Verification of the lock bits is
achieved by observing that their features are enabled.
Chip Erase:
The entire Flash array and the lock bits are
erased electrically by using the proper combination of con-
trol signals and by holding ALE/PROG low for 10 ms. The
code array is written with all “1”s. The chip erase operation
must be executed before the code memory can be re-pro-
grammed.
Reading the Signature Bytes:
The signature bytes are
read by the same procedure as a normal verification of
locations 030H and 031H, except that P3.6 and P3.7 need
to be pulled to a logic low. The values returned are:
(030H) = 1EH indicates manufactured by Atmel
(031H) = 61H indicates 89LV51
(032H) = FFH indicates 12V programming
Program Lock Bits
Protection Type
LB1
LB2
LB3
1
U
U
U
No program lock features.
2
P
U
U
MOVC instructions executed
from external program
memory are disabled from
fetching code bytes from
internal memory, EA is
sampled and latched on
reset, and further
programming of the Flash is
disabled.
3
P
P
U
Same as mode 2, also verify
is disabled.
4
P
P
P
Same as mode 3, also
external execution is
disabled.
V
PP
= 12V
Top-Side Mark
AT89LV51
xxxx
yyww
Signature
(030H) = 1EH
(031H) = 61H
(032H) = FFH
相关PDF资料 |
PDF描述 |
|---|---|
| AT89LV51-12JI | 8-Bit Microcontroller with 4K Bytes Flash |
| AT89LV51-12PC | High Speed CMOS Logic Hex Inverters 14-SOIC -55 to 125 |
| AT89LV51-12PI | 8-Bit Microcontroller with 4K Bytes Flash |
| AT89LV52-12AC | 8-Bit Microcontroller with 8K Bytes Flash |
| AT89LV52-12AI | 8-Bit Microcontroller with 8K Bytes Flash |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT89LV51-12JC-5 | 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LV51-12JI | 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LV51-12PC | 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LV51-12PI | 功能描述:8位微控制器 -MCU 80C31 w/4k RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LV51-12QC-5 | 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。