参数资料
| 型号： | AT90ICEPRO |
| 厂商： | Atmel |
| 文件页数： | 23/35页 |
| 文件大小： | 0K |
| 描述： | AVR GEN PURP IN CIRCUIT EMULATOR |
| 标准包装： | 1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Section 11
External Triggers
The AVR AT90ICEPRO has five external trigger inputs and five trigger outputs, all
located on the AUX connector next to the pod connector.
s The trigger inputs can act as break signals to the emulator, and/or they can be logged
in the trace buffer. If an input is enabled for breaking the emulator, a rising edge on
that input is required to break the emulator.
s
The trigger outputs may be set as trigger points on any instruction in the code window
in AVR Studio. If enabled on an instruction, the output(s) will remain high for one AVR
clock cycle when the marked instruction is executed. This can be used to trigger a
logic analyzer or an oscilloscope.
The details on how to enable and setup triggers and mask registers are presented in the
AVR Studio User Guide.
There are three global mask registers that are used to control the behavior of the trig-
gers:
s The Trigger Output Global Mask Register controls which of the output pins are
allowed to be controlled by the trigger settings in the code. An output pin which is
disabled will remain low even if a trig point for that particular pin is set in the code.
s
s
The Trigger Input Global Mask Register controls which of the input pins are allowed to
break the emulator. If more than one line is enabled, the emulator will break on either
one, but will not store any information about which input caused the event unless you
trace the trigger inputs. Unused lines must either be pulled low or disabled in the
Trigger Input Global Mask Register. Otherwise, the emulator will break on the first line
(on start up, all lines are disabled, so this only applies if input triggers are enabled by
the user).
The External Trace Mask Register controls which of the input pins will be stored in the
trace memory. Input pins that are not enabled in this register will be stored as zero in
the trace memory. To be traced, input signals must be valid and stable at the rising
edge of the AVR clock and for 50 ns thereafter. It is also necessary that the trace
buffer is enabled and turned on.
The trigger input and the external trace are two independent functions acting on the
same input pins. Note that the trigger logic is asynchronous and edge driven, whereas
AT90ICEPRO User Guide
11-1
相关PDF资料 |
PDF描述 |
|---|---|
| AT90USBKEY2 | KIT DEMO FOR AT90USB |
| AT9206 USBPLUGINCARD | KIT EVAL USB QTOUCH PLUGIN/CARD |
| AT9946 | BATTERY BOX FOR DEM KITS |
| ATA6662-EK | BOARD EVALUATION FOR ATA6662 |
| ATADAPCAN01 | EXTENSION CAN ADD-ON TO STK500/1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90L2323-4PC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| AT90L2323-4PI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| AT90L2323-4SC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| AT90L2323-4SI | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| AT90L2343-4PC | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
发布紧急采购，3分钟左右您将得到回复。