参数资料
型号: AT90S1200-12PC
厂商: ATMEL CORP
元件分类: 微控制器/微处理器
英文描述: -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
中文描述: 8-BIT, FLASH, 12 MHz, RISC MICROCONTROLLER, PDIP20
封装: 0.300 INCH, PLASTIC, DIP-20
文件页数: 17/71页
文件大小: 1416K
代理商: AT90S1200-12PC
17
AT90S1200
0838H
AVR
03/02
External Interrupts
The External Interrupt is triggered by the INT0 pin. The interrupt can trigger on rising
edge, falling edge or low level. This is set up as described in the specification for the
MCU Control Register (MCUCR). When INT0 is level triggered, the interrupt is pending
as long as INT0 is held low.
The interrupt is triggered even if INT0 is configured as an output. This provides a way to
generate a software interrupt.
The interrupt flag can not be directly accessed by the user. If an external edge-triggered
interrupt is suspected to be pending, the flag can be cleared as follows.
1.
Disable the External Interrupt by clearing the INT0 flag in GIMSK.
2.
Select level triggered interrupt.
3.
Select desired interrupt edge.
4.
Re-enable the external interrupt by setting INT0 in GIMSK.
Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles
minimum. Four clock cycles after the interrupt flag has been set, the program vector
address for the actual interrupt handling routine is executed. During this 4-clock-cycle
period, the Program Counter (9 bits) is pushed onto the Stack. The vector is normally a
relative jump to the interrupt routine, and this jump takes two clock cycles. If an interrupt
occurs during execution of a multi-cycle instruction, this instruction is completed before
the interrupt is served.
A return from an interrupt handling routine takes four clock cycles. During these four
clock cycles, the Program Counter (9 bits) is popped back from the Stack and the I-flag
in SREG is set. When the AVR exits from an interrupt, it will always return to the main
program and execute one more instruction before any pending interrupt is served.
Note that the Subroutine and Interrupt Stack is a 3-level true hardware stack, and if
more than three nested subroutines and interrupts are executed, only the most recent
three return addresses are stored.
相关PDF资料
PDF描述
AT90S1200 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
AT90S2313 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
AT90S2313-10 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
AT90S2313-10PC -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
AT90S2313-10PI -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
相关代理商/技术参数
参数描述
AT90S1200-12PI 功能描述:IC MCU 1K FLSH 12MHZ IT 20DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:AVR® 90S 标准包装:9 系列:87C 核心处理器:8051 芯体尺寸:8-位 速度:40/20MHz 连通性:UART/USART 外围设备:POR,WDT 输入/输出数:32 程序存储器容量:32KB(32K x 8) 程序存储器类型:OTP EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:0°C ~ 70°C 封装/外壳:40-DIP(0.600",15.24mm) 包装:管件
AT90S1200-12SC 功能描述:8位微控制器 -MCU 1K Flash 5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT90S1200-12SI 功能描述:8位微控制器 -MCU 1k bit RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
AT90S1200-12YC 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 1K Byte of In-System Programmable Flash
AT90S1200-12YI 功能描述:8位微控制器 -MCU 1K Flash 3V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT