- 您现在的位置：买卖IC网 > PDF目录381510 > AT90S1200A (Atmel Corp.) -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash PDF资料下载
参数资料
| 型号： | AT90S1200A |
| 厂商： | Atmel Corp. |
| 元件分类： | 8位微控制器 |
| 英文描述： | -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash |
| 中文描述： | 位AVR微控制器具有8K字节的系统内可编程闪存 |
| 文件页数： | 17/71页 |
| 文件大小： | 1416K |
| 代理商： | AT90S1200A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页
17
AT90S1200
0838H
–
AVR
–
03/02
External Interrupts
The External Interrupt is triggered by the INT0 pin. The interrupt can trigger on rising
edge, falling edge or low level. This is set up as described in the specification for the
MCU Control Register (MCUCR). When INT0 is level triggered, the interrupt is pending
as long as INT0 is held low.
The interrupt is triggered even if INT0 is configured as an output. This provides a way to
generate a software interrupt.
The interrupt flag can not be directly accessed by the user. If an external edge-triggered
interrupt is suspected to be pending, the flag can be cleared as follows.
1.
Disable the External Interrupt by clearing the INT0 flag in GIMSK.
2.
Select level triggered interrupt.
3.
Select desired interrupt edge.
4.
Re-enable the external interrupt by setting INT0 in GIMSK.
Interrupt Response Time
The interrupt execution response for all the enabled AVR interrupts is four clock cycles
minimum. Four clock cycles after the interrupt flag has been set, the program vector
address for the actual interrupt handling routine is executed. During this 4-clock-cycle
period, the Program Counter (9 bits) is pushed onto the Stack. The vector is normally a
relative jump to the interrupt routine, and this jump takes two clock cycles. If an interrupt
occurs during execution of a multi-cycle instruction, this instruction is completed before
the interrupt is served.
A return from an interrupt handling routine takes four clock cycles. During these four
clock cycles, the Program Counter (9 bits) is popped back from the Stack and the I-flag
in SREG is set. When the AVR exits from an interrupt, it will always return to the main
program and execute one more instruction before any pending interrupt is served.
Note that the Subroutine and Interrupt Stack is a 3-level true hardware stack, and if
more than three nested subroutines and interrupts are executed, only the most recent
three return addresses are stored.
相关PDF资料 |
PDF描述 |
|---|---|
| AT90S1200-12PC | -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash |
| AT90S1200 | -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash |
| AT90S2313 | -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash |
| AT90S2313-10 | -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash |
| AT90S2313-10PC | -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90S1200A-12PC | 功能描述:8位微控制器 -MCU 1K Flash 5V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT90S1200A-12PI | 制造商:Atmel Corporation 功能描述:MCU 8BIT AT90 RISC 1KB FLASH 3.3V/5V 20PDIP - Rail/Tube |
| AT90S1200A-12SC | 制造商:Atmel Corporation 功能描述:MCU 8BIT AT90 RISC 1KB FLASH 3.3V/5V 20SOIC - Rail/Tube |
| AT90S1200A-12SI | 制造商:Atmel Corporation 功能描述:MCU 8BIT AT90 RISC 1KB FLASH 3.3V/5V 20SOIC - Rail/Tube |
| AT90S1200A-12YC | 功能描述:IC MCU 8BIT 1KB FLASH 20SSOP 制造商:microchip technology 系列:AVR? 90S 包装:管件 零件状态:停產 核心处理器:AVR 核心尺寸:8-位 速度:12MHz 连接性:SPI 外设:POR，WDT I/O 数:15 程序存储容量:1KB（512 x 16） 程序存储器类型:闪存 EEPROM 容量:64 x 8 RAM 容量:- 电压 - 电源（Vcc/Vdd）:4 V ~ 6 V 数据转换器:- 振荡器类型:内部 工作温度:0°C ~ 70°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商器件封装:20-SSOP 基本零件编号:AT90S1200 标准包装:67 |
发布紧急采购，3分钟左右您将得到回复。