- 您现在的位置：买卖IC网 > PDF目录12057 > AT90USB82-16MU (Atmel)IC AVR MCU 8K FLASH 32QFN PDF资料下载
参数资料
| 型号： | AT90USB82-16MU |
| 厂商： | Atmel |
| 文件页数： | 29/38页 |
| 文件大小： | 0K |
| 描述： | IC AVR MCU 8K FLASH 32QFN |
| 产品培训模块： | MCU Product Line Introduction megaAVR Introduction |
| 标准包装： | 2,450 |
| 系列： | AVR® 90USB |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | EBI/EMI，PS/2，SPI，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 22 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 包装： | 托盘 |
| 产品目录页面： | 611 (CN2011-ZH PDF) |
| 配用： | ATSTK600-TQFP32-ND - STK600 SOCKET/ADAPTER 32-TQFP ATSTK526-ND - KIT STARTER FOR AT90USB82/162 ATAVRDRAGON-ND - KIT DRAGON FLASH MEM AVR ATSTK525-ND - KIT STARTER FOR AT90USB AT90USBKEY2-ND - KIT DEMO FOR AT90USB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
35
7707F–AVR–11/10
AT90USB82/162
the system clock frequency and the power consumption when the requirement for processing
power is low. This can be used with all clock source options, and it will affect the clock frequency
of the CPU and all synchronous peripherals. clk
I/O, clkCPU, and clkFLASH are divided by a factor as
shown in Table 6-9.
When switching between prescaler settings, the System Clock Prescaler ensures that no
glitches occurs in the clock system. It also ensures that no intermediate frequency is higher than
neither the clock frequency corresponding to the previous setting, nor the clock frequency corre-
sponding to the new setting.
The ripple counter that implements the prescaler runs at the frequency of the undivided clock,
which may be faster than the CPU's clock frequency. Hence, it is not possible to determine the
state of the prescaler - even if it were readable, and the exact time it takes to switch from one
clock division to the other cannot be exactly predicted. From the time the CLKPS values are writ-
ten, it takes between T1 + T2 and T1 + 2 * T2 before the new clock frequency is active. In this
interval, 2 active clock edges are produced. Here, T1 is the previous clock period, and T2 is the
period corresponding to the new prescaler setting.
To avoid unintentional changes of clock frequency, a special write procedure must be followed
to change the CLKPS bits:
1.
Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bits in
CLKPR to zero.
2.
Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.
Interrupts must be disabled when changing prescaler setting to make sure the write procedure is
not interrupted.
6.8.1
Clock Prescale Register – CLKPR
Bit 7 – CLKPCE: Clock Prescaler Change Enable
The CLKPCE bit must be written to logic one to enable change of the CLKPS bits. The CLKPCE
bit is only updated when the other bits in CLKPR are simultaneously written to zero. CLKPCE is
cleared by hardware four cycles after it is written or when CLKPS bits are written. Rewriting the
CLKPCE bit within this time-out period does neither extend the time-out period, nor clear the
CLKPCE bit.
Bit 6-4 - Reserved bits
These bits are reserved and will always read as zero.
Bits 3..0 – CLKPS3..0: Clock Prescaler Select Bits 3 - 0
These bits define the division factor between the selected clock source and the internal system
clock. These bits can be written run-time to vary the clock frequency to suit the application
requirements. As the divider divides the master clock input to the MCU, the speed of all synchro-
nous peripherals is reduced when a division factor is used. The division factors are given in
The CKDIV8 Fuse determines the initial value of the CLKPS bits. If CKDIV8 is unprogrammed,
the CLKPS bits will be reset to “0000”. If CKDIV8 is programmed, CLKPS bits are reset to
Bit
7
6
543
2
1
0
CLKPCE
–
CLKPS3
CLKPS2
CLKPS1
CLKPS0
CLKPR
Read/Write
R/W
R
R/W
Initial Value
0
See Bit Description
相关PDF资料 |
PDF描述 |
|---|---|
| ATMEGA48P-20PU | MCU AVR 4K ISP FLASH 20MHZ 28DIP |
| VI-JT3-IX-B1 | CONVERTER MOD DC/DC 24V 75W |
| P89LPC935FA,129 | IC 80C51 MCU FLASH 8K 28-PLCC |
| P89LPC932A1FA,129 | IC 80C51 MCU FLASH 8K 28-PLCC |
| AT89C51RC-24JU | IC 8051 MCU FLASH 32K 44PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90USB82-16MUR | 功能描述:8位微控制器 -MCU 8K Flash RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT90USBKEY | 功能描述:开发板和工具包 - AVR Demo board f/AVR MCU & AT90USB RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT90USBKEY2 | 功能描述:开发板和工具包 - AVR AVR USB Eval Kit RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| AT-910 | 制造商:HRS 制造商全称:HRS 功能描述:Stripline Mounting Fixed Attenuators (DC to 8 GHz) |
| AT-910(40) | 功能描述:衰减器 -IC RoHS:否 制造商:Skyworks Solutions, Inc. 最大衰减:18 dB 容差: 阻抗: 功率额定值:30 dBm 安装风格:SMD/SMT 工作温度范围:- 40 C to + 85 C |
发布紧急采购，3分钟左右您将得到回复。