参数资料
| 型号： | AT91SAM7S64-AU-999 |
| 厂商： | Atmel |
| 文件页数： | 6/50页 |
| 文件大小： | 0K |
| 描述： | IC MCU ARM7 64KB FLASH 64LQFP |
| 标准包装： | 1,500 |
| 系列： | SAM7S |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 连通性： | I²C，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 64KB（64K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 16K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 64-LQFP |
| 包装： | 带卷 (TR) |
| 配用： | AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9 AT91SAM7S-EK-ND - KIT EVAL FOR ARM AT91SAM7S |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
14
SAM7S Series [DATASHEET]
6175KS–ATARM–25-Oct-12
6.
I/O Lines Considerations
6.1
JTAG Port Pins
TMS, TDI and TCK are schmitt trigger inputs. TMS and TCK are 5-V tolerant, TDI is not. TMS, TDI and TCK do not
integrate a pull-up resistor.
TDO is an output, driven at up to VDDIO, and has no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. The JTAGSEL pin integrates
a permanent pull-down resistor of about 15 k
Ω to GND, so that it can be left unconnected for normal operations.
6.2
Test Pin
The TST pin is used for manufacturing test, fast programming mode or SAM-BA Boot Recovery of the SAM7S Series
when asserted high. The TST pin integrates a permanent pull-down resistor of about 15 k
Ω to GND, so that it can be left
unconnected for normal operations.
To enter fast programming mode, the TST pin and the PA0 and PA1 pins should be tied high and PA2 tied to low.
To enter SAM-BA Boot Recovery, the TST pin and the PA0, PA1 and PA2 pins should be tied high for at least 10
seconds. Then a power cycle of the board is mandatory.
Driving the TST pin at a high level while PA0 or PA1 is driven at 0 leads to unpredictable results.
6.3
Reset Pin
The NRST pin is bidirectional with an open drain output buffer. It is handled by the on-chip reset controller and can be
driven low to provide a reset signal to the external components or asserted low externally to reset the microcontroller.
There is no constraint on the length of the reset pulse, and the reset controller can guarantee a minimum pulse length.
This allows connection of a simple push-button on the pin NRST as system user reset, and the use of the signal NRST to
reset all the components of the system.
The NRST pin integrates a permanent pull-up resistor to VDDIO.
6.4
ERASE Pin
The ERASE pin is used to re-initialize the Flash content and some of its NVM bits. It integrates a permanent pull-down
resistor of about 15 k
Ω to GND, so that it can be left unconnected for normal operations.
6.5
PIO Controller A Lines
All the I/O lines PA0 to PA31on SAM7S512/256/128/64/321 (PA0 to PA20 on SAM7S32) are 5V-tolerant and all
integrate a programmable pull-up resistor.
All the I/O lines PA0 to PA31 on SAM7S161 (PA0 to PA20 on SAM7S16) are not 5V-tolerant and all integrate a
programmable pull-up resistor.
Programming of this pull-up resistor is performed independently for each I/O line through the PIO controllers.
5V-tolerant means that the I/O lines can drive voltage level according to VDDIO, but can be driven with a voltage of up to
5.5V. However, driving an I/O line with a voltage over VDDIO while the programmable pull-up resistor is enabled will
create a current path through the pull-up resistor from the I/O line to VDDIO. Care should be taken, in particular at reset,
as all the I/O lines default to input with the pull-up resistor enabled at reset.
6.6
I/O Line Drive Levels
The PIO lines PA0 to PA3 are high-drive current capable. Each of these I/O lines can drive up to 16 mA permanently.
The remaining I/O lines can draw only 8 mA.
However, the total current drawn by all the I/O lines cannot exceed 150 mA (100 mA for SAM7S32/16).
相关PDF资料 |
PDF描述 |
|---|---|
| AT91SAM7XC128-AU-999 | IC MCU ARM7 128KB FLASH 100LQFP |
| AT91SAM7S32-AU-999 | IC MCU ARM7 32KB FLASH 48LQFP |
| PIC18F4515-I/P | IC MCU FLASH 24KX16 40DIP |
| PIC16F84-04I/SO | IC MCU FLASH 1KX14 EE 18SOIC |
| DSPIC33FJ64GP802-E/MM | IC DSPIC MCU/DSP 64K 28-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91SAM7S64B-AU | 功能描述:ARM微控制器 - MCU Industrial Temp MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7S64B-AU-999 | 功能描述:ARM微控制器 - MCU Industrial Temp MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7S64B-MU | 功能描述:ARM微控制器 - MCU Industrial Temp MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7S64B-MU-999 | 功能描述:ARM微控制器 - MCU Industrial Temp MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7S64C-AU | 功能描述:ARM微控制器 - MCU 64K Flash SRAM 16K ARM based MCU RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。