参数资料
| 型号： | AT91SAM7SE32-AU |
| 厂商： | Atmel |
| 文件页数： | 7/47页 |
| 文件大小： | 0K |
| 描述： | MCU ARM 32K HS FLASH 128-LQFP |
| 产品培训模块： | SAM9 MPU Boot Solutions & Application Deployment MCU Product Line Introduction |
| 产品变化通告： | AT91SAM7SE32 Obsolescence 10/May/2012 |
| 标准包装： | 72 |
| 系列： | SAM7SE |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 连通性： | EBI/EMI，I²C，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 88 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 128-LQFP |
| 包装： | 托盘 |
| 配用： | AT91SAM7SE-EK-ND - EVAL BOARD FOR AT91SAM7SE AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
15
6222GS–ATARM–6-Sep-11
SAM7SE512/256/32 Summary
6.
/O Lines Considerations
6.1
JTAG Port Pins
TMS, TDI and TCK are Schmitt trigger inputs. TMS, TDI and TCK do not integrate a pull-up
resistor.
TDO is an output, driven at up to VDDIO, and has no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. The
JTAGSEL pin integrates a permanent pull-down resistor of about 15 k
Ω.
To eliminate any risk of spuriously entering the JTAG boundary scan mode due to noise on
JTAGSEL, it should be tied externally to GND if boundary scan is not used, or put in place an
external low value resistor (such as 1 k
Ω) .
6.2
Test Pin
Th e T S T p i n is used f o r ma nu f a ct ur in g t e st o r f a st pr og ra mmi ng mod e of t h e
SAM7SE512/256/32 when asserted high. The TST pin integrates a permanent pull-down resis-
tor of about 15 k
Ω to GND.
To eliminate any risk of entering the test mode due to noise on the TST pin, it should be tied to
GND if the FFPI is not used, or put in place an external low value resistor (such as 1 k
Ω) .
To enter fast programming mode, the TST pin and the PA0 and PA1 pins should be tied high
and PA2 tied low.
Driving the TST pin at a high level while PA0 or PA1 is driven at 0 leads to unpredictable results.
6.3
Reset Pin
The NRST pin is bidirectional with an open-drain output buffer. It is handled by the on-chip reset
controller and can be driven low to provide a reset signal to the external components or asserted
low externally to reset the microcontroller. There is no constraint on the length of the reset pulse,
and the reset controller can guarantee a minimum pulse length. This allows connection of a sim-
ple push-button on the NRST pin as system user reset, and the use of the NRST signal to reset
all the components of the system.
An external power-on reset can drive this pin during the start-up instead of using the internal
power-on reset circuit.
The NRST pin integrates a permanent pull-up of about 100 k
Ω resistor to VDDIO.
This pin has Schmitt trigger input.
6.4
ERASE Pin
The ERASE pin is used to re-initialize the Flash content and some of its NVM bits. It integrates a
permanent pull-down resistor of about 15 k
Ω to GND.
To eliminate any risk of erasing the Flash due to noise on the ERASE pin, it should be tied exter-
nally to GND, which prevents erasing the Flash from the application, or put in place an external
low value resistor (such as 1 k
Ω) .
This pin is debounced by the RC oscillator to improve the glitch tolerance. When the pin is tied to
high during less than 100 ms, ERASE pin is not taken into account. The pin must be tied high
during more than 220 ms to perform the re-initialization of the Flash.
相关PDF资料 |
PDF描述 |
|---|---|
| AT91SAM7X256B-CU | IC MCU 256KB FLASH 100TFBGA |
| AT91SAM7XC256B-AU | MCU ARM 256K HS FLASH 100-LQFP |
| AT91SAM9260B-CU-100 | IC MCU ARM9 217LFBGA |
| AT91SAM9260B-CU-999 | IC MCU ARM9 217LFBGA |
| AT91SAM9261-CJ-999 | IC MCU ARM9 ULTRA LP 217LFBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91SAM7SE32B-AU | 功能描述:ARM微控制器 - MCU LQFP Grn IT MRLB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE32B-AUR | 功能描述:ARM微控制器 - MCU LQFP Green IND TEMP MRL B, T&R MRLC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE32B-CU | 功能描述:ARM微控制器 - MCU BGA Grn IT MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE32B-CUR | 功能描述:ARM微控制器 - MCU BGA Grn IT MRLB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE32-CU | 功能描述:ARM微控制器 - MCU BGA IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。