- 您现在的位置：买卖IC网 > PDF目录12024 > AT91SAM7SE32B-CU (Atmel)IC MCU ARM7 32KB FLASH 144LFBGA PDF资料下载
参数资料
| 型号： | AT91SAM7SE32B-CU |
| 厂商： | Atmel |
| 文件页数： | 19/47页 |
| 文件大小： | 0K |
| 描述： | IC MCU ARM7 32KB FLASH 144LFBGA |
| 标准包装： | 240 |
| 系列： | SAM7SE |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 连通性： | EBI/EMI，I²C，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 88 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 8K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 144-LFBGA |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
26
6222GS–ATARM–6-Sep-11
SAM7SE512/256/32 Summary
The security bit can only be enabled through the Command “Set Security Bit” of the EFC User
Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1 and
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 200 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.1.2.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
GPNVM bit 0 is used as a brownout detector enable bit. Setting the GPNVM bit 0 enables the
BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM bit 0 and thus
disables the brownout detector by default.
GPNVM bit 1 is used as a brownout reset enable signal for the reset controller. Setting the
GPNVM bit 1 enables the brownout reset when a brownout is detected, Clearing the GPNVM
bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by default.
8.1.2.6
Calibration Bits
Sixteen NVM bits are used to calibrate the brownout detector and the voltage regulator. These
bits are factory configured and cannot be changed by the user. The ERASE pin has no effect on
the calibration bits.
8.1.3
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high and PA2 tied to low.
The Flash of the SAM7SE512 is organized in 2048 pages of 256 bytes (dual plane). It reads
as 131,072 32-bit words.
The Flash of the SAM7SE256 is organized in 1024 pages of 256 bytes (single plane). It reads
as 65,536 32-bit words.
The Flash of the SAM7SE32 is organized in 256 pages of 128 bytes (single plane). It reads
as 32,768 32-bit words.
The Flash of the SAM7SE512/256 contains a 256-byte write buffer, accessible through a 32-
bit interface.
The Flash of the SAM7SE32 contains a 128-byte write buffer, accessible through a 32-bit
interface.
相关PDF资料 |
PDF描述 |
|---|---|
| AT91SAM9R64-CU | IC MCU ARM9 32KB ROM 144LFBGA |
| AT89C51CC03UA-S3SUM | IC 8051 MCU 64K FLASH 52-PLCC |
| VI-J4B-IY-F3 | CONVERTER MOD DC/DC 95V 50W |
| LPC2294HBD144,551 | IC ARM7 MCU FLASH 256K 144-LQFP |
| AT89C51CC03CA-S3SUM | IC 8051 MCU FLASH 64K 52-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91SAM7SE32B-CUR | 功能描述:ARM微控制器 - MCU BGA Grn IT MRLB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE32-CU | 功能描述:ARM微控制器 - MCU BGA IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE32-CU-999 | 功能描述:ARM微控制器 - MCU BGA Ind. Temp Green RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE512 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Thumb-based Microcontrollers |
| AT91SAM7SE512_08 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Incorporates the ARM7TDMI ARM Thumb Processor |
发布紧急采购，3分钟左右您将得到回复。