- 您现在的位置：买卖IC网 > PDF目录11201 > AT91SAM7SE512-AU-999 (Atmel)IC MCU ARM7 512KB FLASH 128LQFP PDF资料下载
参数资料
| 型号： | AT91SAM7SE512-AU-999 |
| 厂商： | Atmel |
| 文件页数： | 24/47页 |
| 文件大小： | 0K |
| 描述： | IC MCU ARM7 512KB FLASH 128LQFP |
| 产品培训模块： | MCU Product Line Introduction |
| 标准包装： | 750 |
| 系列： | SAM7SE |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 连通性： | EBI/EMI，I²C，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 88 |
| 程序存储器容量： | 512KB（512K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 32K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 128-LQFP |
| 包装： | 带卷 (TR) |
| 配用： | AT91SAM7SE-EK-ND - EVAL BOARD FOR AT91SAM7SE AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
30
6222GS–ATARM–6-Sep-11
SAM7SE512/256/32 Summary
9.1
Reset Controller
Based on one power-on reset cell and a double brownout detector
Status of the last reset, either Power-up Reset, Software Reset, User Reset, Watchdog
Reset, Brownout Reset
Controls the internal resets and the NRST pin output
Allows to shape a signal on the NRST line, guaranteeing that the length of the pulse meets
any requirement.
9.1.1
Brownout Detector and Power On Reset
The SAM7SE512/256/32 embeds one brownout detection circuit and a power-on reset cell. The
power-on reset is supplied with and monitors VDDCORE.
Both signals are provided to the Flash to prevent any code corruption during power-up or power-
down sequences or if brownouts occur on the VDDCORE power supply.
The power-on reset cell has a limited-accuracy threshold at around 1.5V. Its output remains low
during power-up until VDDCORE goes over this voltage level. This signal goes to the reset con-
troller and allows a full re-initialization of the device.
The brownout detector monitors the VDDCORE and VDDFLASH levels during operation by
comparing it to a fixed trigger level. It secures system operations in the most difficult environ-
ments and prevents code corruption in case of brownout on the VDDCORE or VDDFLASH.
When the brownout detector is enabled and VDDCORE decreases to a value below the trigger
level (Vbot18-, defined as Vbot18 - hyst/2), the brownout output is immediately activated.
When VDDCORE increases above the trigger level (Vbot18+, defined as Vbot18 + hyst/2), the
reset is released. The brownout detector only detects a drop if the voltage on VDDCORE stays
below the threshold voltage for longer than about 1s.
The VDDCORE threshold voltage has a hysteresis of about 50 mV, to ensure spike free brown-
out detection. The typical value of the brownout detector threshold is 1.68V with an accuracy of
± 2% and is factory calibrated.
When the brownout detector is enabled and VDDFLASH decreases to a value below the trigger
level (Vbot33-, defined as Vbot33 - hyst/2), the brownout output is immediately activated.
When VDDFLASH increases above the trigger level (Vbot33+, defined as Vbot33 + hyst/2), the
reset is released. The brownout detector only detects a drop if the voltage on VDDCORE stays
below the threshold voltage for longer than about 1s.
The VDDFLASH threshold voltage has a hysteresis of about 50 mV, to ensure spike free brown-
out detection. The typical value of the brownout detector threshold is 2.80V with an accuracy of
± 3.5% and is factory calibrated.
The brownout detector is low-power, as it consumes less than 20 A static current. However, it
can be deactivated to save its static current. In this case, it consumes less than 1A. The deac-
tivation is configured through the GPNVM bit 0 of the Flash.
9.2
Clock Generator
The Clock Generator embeds one low-power RC Oscillator, one Main Oscillator and one PLL
with the following characteristics:
RC Oscillator ranges between 22 KHz and 42 KHz
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7026BSTZ62-RL | IC MCU 12BIT 1MSPS UART 80-LQFP |
| ADUC7026BSTZ62I-RL | IC MCU 12BIT 1MSPS I2C 80-LQFP |
| NLAST4501DTT1G | IC SWITCH SPST 5TSOP |
| ADUC7019BCPZ62I | IC MCU FLSH 62K ANLG I/O 40LFCSP |
| AT32UC3C2512C-A2ZR | IC MCU 32BIT 512KB FLASH 64TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91SAM7SE512B-AU | 功能描述:ARM微控制器 - MCU IND TEMP MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE512B-AUR | 功能描述:ARM微控制器 - MCU IND TEMP MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE512B-CU | 功能描述:ARM微控制器 - MCU IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE512B-CUR | 功能描述:ARM微控制器 - MCU IND TEMP MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7SE512-CU | 功能描述:ARM微控制器 - MCU 512kB Flash 32kB SRAM 48MHz 4 PWM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。