- 您现在的位置：买卖IC网 > PDF目录11199 > AT91SAM7X128C-AU (Atmel)IC MCU 32BIT 128KB FLASH 100LQFP PDF资料下载
参数资料
| 型号： | AT91SAM7X128C-AU |
| 厂商： | Atmel |
| 文件页数： | 15/44页 |
| 文件大小： | 0K |
| 描述： | IC MCU 32BIT 128KB FLASH 100LQFP |
| 产品培训模块： | SAM9 MPU Boot Solutions & Application Deployment AT91SAM7X and SAM7XC Flash-based Microcontrollers MCU Product Line Introduction |
| 标准包装： | 90 |
| 系列： | SAM7X |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 连通性： | CAN，以太网，I²C，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 62 |
| 程序存储器容量： | 128KB（128K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 32K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
22
6120GS–ATARM–07-Apr-11
SAM7X512/256/128 Summary
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 220 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.5.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
GPNVM Bit 0 is used as a brownout detector enable bit. Setting the GPNVM Bit 0 enables
the BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM Bit 0 and thus
disables the brownout detector by default.
The GPNVM Bit 1 is used as a brownout reset enable signal for the reset controller. Setting
the GPNVM Bit 1 enables the brownout reset when a brownout is detected, Clearing the
GPNVM Bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by
default.
8.5.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits
are factory configured and cannot be changed by the user. The ERASE pin has no effect on the
calibration bits.
8.6
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high.
8.7
SAM-BA Boot Assistant
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program in-
situ the on-chip Flash memory.
The SAM-BA Boot Assistant supports serial communication via the DBGU or the USB Device
Port.
Communication via the DBGU supports a wide range of crystals from 3 to 20 MHz via
software auto-detection.
Communication via the USB Device Port is limited to an 18.432 MHz crystal.
The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).
The SAM-BA Boot is in ROM and is mapped at address 0x0 when the GPNVM Bit 2 is set to 0.
When GPNVM bit 2 is set to 1, the device boots from the Flash.
When GPNVM bit 2 is set to 0, the device boots from ROM (SAM-BA).
相关PDF资料 |
PDF描述 |
|---|---|
| NC7WB66L8X | IC SWITCH DUAL SPST-NO 8MICROPAK |
| MC74HCT4051ADR2G | ANALOG MULTIPLEXERS/DEMU SOIC16 |
| VE-B4P-IX | CONVERTER MOD DC/DC 13.8V 75W |
| ATMEGA128-16AUR | MCU AVR 128KB FLASH 16MHZ 64TQFP |
| M74HCT4051ADTR2G | ANALOG MULTIPLEXERS/DEMU TSSOP16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91SAM7X128C-AUR | 功能描述:ARM微控制器 - MCU LQFP Green IND TEMP MRL B, T&R MRLC RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7X128C-CU | 功能描述:微处理器 - MPU TFBGA GRN IND TEMP MRL C RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| AT91SAM7X128C-CUR | 制造商:Atmel Corporation 功能描述:TFBGA, GREEN, IND TEMP, MRL, C - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU ARM7 128KB FLASH 100TFBGA |
| AT91SAM7X128-CU | 功能描述:ARM微控制器 - MCU . - BGA IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
| AT91SAM7X128-CU-999 | 功能描述:ARM微控制器 - MCU Green, Ind Temp RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 处理器系列:STM32F373xx 数据总线宽度:32 bit 最大时钟频率:72 MHz 程序存储器大小:256 KB 数据 RAM 大小:32 KB 片上 ADC:Yes 工作电源电压:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:LQFP-48 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。