- 您现在的位置：买卖IC网 > PDF目录12015 > AT91SAM7XC512-CU (Atmel)MCU ARM 512K HS FLASH 100-TFBGA PDF资料下载
参数资料
| 型号： | AT91SAM7XC512-CU |
| 厂商： | Atmel |
| 文件页数： | 6/47页 |
| 文件大小： | 0K |
| 描述： | MCU ARM 512K HS FLASH 100-TFBGA |
| 产品培训模块： | SAM9 MPU Boot Solutions & Application Deployment AT91SAM7X and SAM7XC Flash-based Microcontrollers MCU Product Line Introduction |
| 标准包装： | 260 |
| 系列： | SAM7XC |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 连通性： | CAN，以太网，I²C，SPI，SSC，UART/USART，USB |
| 外围设备： | 欠压检测/复位，DMA，POR，PWM，WDT |
| 输入/输出数： | 62 |
| 程序存储器容量： | 512KB（512K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 128K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 100-TFBGA |
| 包装： | 托盘 |
| 配用： | AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9 AT91SAM7XC-EK-ND - KIT EVAL FOR AT91SAM7XC256/128 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
14
6209DS–ATARM–17-Feb-09
AT91SAM7XC512/256/128
6.
I/O Lines Considerations
6.1
JTAG Port Pins
TMS, TDI and TCK are schmitt trigger inputs and are not 5-V tolerant. TMS, TDI and TCK do not
integrate a pull-up resistor.
TDO is an output, driven at up to VDDIO, and has no pull-up resistor.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. The
JTAGSEL pin integrates a permanent pull-down resistor of about 15 k
Ω.
To eliminate any risk of spuriously entering the JTAG boundary scan mode due to noise on
JTAGSEL, it should be tied externally to GND if boundary scan is not used, or pulled down with
an external low-value resistor (such as 1 k
Ω) .
6.2
Test Pin
Th e T S T p i n is used f o r ma nu f a ct ur in g t e st o r f a st pr og ra mmi ng mod e of t h e
AT91SAM7XC512/256/128 when asserted high. The TST pin integrates a permanent pull-down
resistor of about 15 k
Ω to GND.
To eliminate any risk of entering the test mode due to noise on the TST pin, it should be tied to
GND if the FFPI is not used, or pulled down with an external low-value resistor (such as 1 k
Ω) .
To enter fast programming mode, the TST pin and the PA0 and PA1 pins should be tied high
and PA2 tied to low.
Driving the TST pin at a high level while PA0 or PA1 is driven at 0 leads to unpredictable results.
6.3
Reset Pin
The NRST pin is bidirectional with an open drain output buffer. It is handled by the on-chip reset
controller and can be driven low to provide a reset signal to the external components or asserted
low externally to reset the microcontroller. There is no constraint on the length of the reset pulse,
and the reset controller can guarantee a minimum pulse length. This allows connection of a sim-
ple push-button on the NRST pin as system user reset, and the use of the signal NRST to reset
all the components of the system.
The NRST pin integrates a permanent pull-up resistor to VDDIO
.
6.4
ERASE Pin
The ERASE pin is used to re-initialize the Flash content and some of its NVM bits. It integrates a
permanent pull-down resistor of about 15 k
Ω to GND.
To eliminate any risk of erasing the Flash due to noise on the ERASE pin, it shoul be tied exter-
nally to GND, which prevents erasing the Flash from the applicatiion, or pulled down with an
external low-value resistor (such as 1 k
Ω) .
This pin is debounced by the RC oscillator to improve the glitch tolerance. Minimum debouncing
time is 200 ms.
6.5
PIO Controller Lines
All the I/O lines, PA0 to PA30 and PB0 to PB30, are 5V-tolerant and all integrate a programma-
ble pull-up resistor. Programming of this pull-up resistor is performed independently for each I/O
line through the PIO controllers.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JVR-IY-F1 | CONVERTER MOD DC/DC 7.5V 50W |
| VE-B3D-IY-F3 | CONVERTER MOD DC/DC 85V 50W |
| ADUC834BSZ | IC ADC DUAL16/24BIT W/MCU 52MQFP |
| VI-JVP-IY-F2 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-B3D-IY-F2 | CONVERTER MOD DC/DC 85V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT91SAM7XC-EK | 功能描述:开发板和工具包 - ARM Eval Kit for AT91SAM7XC MCU RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| AT91SAM7X-EK | 功能描述:开发板和工具包 - ARM Eval Kit for AT91SAM7X MCU RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| AT91SAM9260 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers |
| AT91SAM9260_06 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Thumb Microcontrollers |
| AT91SAM9260_08 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AT91 ARM Thumb Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。