- 您现在的位置：买卖IC网 > Datasheet目录314 > AT93C46E-TH-T (Atmel)IC EEPROM 1KBIT 2MHZ 8TSSOP Datasheet资料下载
参数资料
| 型号： | AT93C46E-TH-T |
| 厂商： | Atmel |
| 文件页数： | 5/17页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 1KBIT 2MHZ 8TSSOP |
| 标准包装： | 5,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 1K (64 x 16) |
| 速度： | 250kHz，1MHz，2MHz |
| 接口： | Microwire 3 线串行 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
AT93C46E
Table 3-1.
Instruction Set for the AT93C46E
Address
Instruction
READ
EWEN
ERASE
WRITE
ERAL
WRAL
EWDS
SB
1
1
1
1
1
1
1
Op Code
10
00
11
01
00
00
00
x 16
A 5 ? A 0
11XXXX
A 5 ? A 0
A 5 ? A 0
10XXXX
01XXXX
00XXXX
Comments
Reads data stored in memory, at specified address
Write enable must precede all programming modes
Erase memory location A n ? A 0
Writes memory location A n ? A 0
Erases all memory locations. Valid only at V CC = 4.5V to 5.5V
Writes all memory locations. Valid only at V CC = 4.5V to 5.5V
Disables all programming instructions
READ (READ): The Read (READ) instruction contains the address code for the memory loca-
tion to be read. After the instruction and address are decoded, data from the selected memory
location is available at the serial output pin DO. Output data changes are synchronized with the
rising edges of serial clock SK. It should be noted that a dummy bit (logic “0”) precedes the 16-
bit data output string.
ERASE/WRITE ENABLE (EWEN): To assure data integrity, the part automatically goes into the
Erase/Write Disable (EWDS) state when power is first applied. An Erase/Write Enable (EWEN)
instruction must be executed first before any programming instructions can be carried out.
Please note that once in the EWEN state, programming remains enabled until an EWDS instruc-
tion is executed or V CC power is removed from the part.
ERASE (ERASE): The Erase (ERASE) instruction programs all bits in the specified memory
location to the logical “1” state. The self-timed erase cycle starts once the Erase instruction and
address are decoded. The DO pin outputs the ready/busy status of the part if CS is brought high
after being kept low for a minimum of 250 ns (t CS ). A logic “1” at pin DO indicates that the
selected memory location has been erased and the part is ready for another instruction.
WRITE (WRITE): The Write (WRITE) instruction contains the 16 bits of data to be written into
the specified memory location. The self-timed programming cycle, t WP , starts after the last bit of
data is received at serial data input pin DI. The DO pin outputs the ready/busy status of the part
if CS is brought high after being kept low for a minimum of 250 ns (t CS ). A logic “0” at DO indi-
cates that programming is still in progress. A logic “1” indicates that the memory location at the
specified address has been written with the data pattern contained in the instruction and the part
is ready for further instructions. A ready/busy status cannot be obtained if the CS is brought
high after the end of the self-timed programming cycle, t WP .
ERASE ALL (ERAL): The Erase All (ERAL) instruction programs every bit in the memory array
to the logic “1 ” state and is primarily used for testing purposes. The DO pin outputs the
ready/busy status of the part if CS is brought high after being kept low for a minimum of 250 ns
(t CS ). The ERAL instruction is valid only at V CC = 5.0V ± 10%.
WRITE ALL (WRAL): The Write All (WRAL) instruction programs all memory locations with the
data patterns specified in the instruction. The DO pin outputs the ready/busy status of the part if
CS is brought high after being kept low for a minimum of 250 ns (t CS ). The WRAL instruction is
valid only at V CC = 5.0V ± 10%.
5
5207D–SEEPR–1/08
相关PDF资料 |
PDF描述 |
|---|---|
| AT93C46Y6-10YH-1.8 | IC EEPROM 1KBIT 2MHZ 8DFN |
| AT93C56A-10TU-2.7 | IC EEPROM 2KBIT 2MHZ 8TSSOP |
| AT93C86AY6-10YH-1.8 | IC EEPROM 16KBIT 2MHZ 8MAP |
| ATAVRBFLY | KIT EVALUATION AVR BUTTERFLY |
| ATAVRXBNDL | XMEGA XPLAIN AND DISPLAY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT93C46R-10SC | 功能描述:IC EEPROM 1KBIT 2MHZ 8SOIC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT93C46R-10SC-1.8 | 功能描述:电可擦除可编程只读存储器 1k 3-Wire Bus RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT93C46R-10SC-2.5 | 功能描述:IC EEPROM 1KBIT 2MHZ 8SOIC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT93C46R-10SC-2.7 | 功能描述:IC EEPROM 1KBIT 2MHZ 8SOIC RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT93C46R-10SI | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:3-wire Serial EEPROMs |
发布紧急采购，3分钟左右您将得到回复。