- 您现在的位置：买卖IC网 > PDF目录223426 > AT93C56A-10PI-1.8 (ATMEL CORP) 3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16) PDF资料下载
参数资料
| 型号： | AT93C56A-10PI-1.8 |
| 厂商： | ATMEL CORP |
| 元件分类： | PROM |
| 英文描述： | 3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16) |
| 中文描述： | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDIP8 |
| 封装： | 0.300 INCH, PLASTIC, MS-001BA, DIP-8 |
| 文件页数： | 13/17页 |
| 文件大小： | 277K |
| 代理商： | AT93C56A-10PI-1.8 |
5
AT93C56A/66A [Preliminary]
3378H–SEEPR–8/05
Note:
The X’s in the address field represent don’t care values and must be clocked.
Functional Description
The AT93C56A/66A is accessed via a simple and versatile three-wire serial communi-
cation interface. Device operation is controlled by seven instructions issued by the host
processor. A valid instruction starts with a rising edge of CS and consists of a Start
Bit (logic “1”) followed by the appropriate Op Code and the desired memory address
location.
READ (READ): The Read (READ) instruction contains the address code for the mem-
ory location to be read. After the instruction and address are decoded, data from the
selected memory location is available at the serial output pin DO. Output data changes
are synchronized with the rising edges of serial clock SK. It should be noted that a
dummy bit (logic “0”) precedes the 8- or 16-bit data output string. The AT93C56A/66A
supports sequential read operations. The device will automatically increment the inter-
nal address pointer and clock out the next memory location as long as Chip Select (CS)
is held high. In this case, the dummy bit (logic “0”) will not be clocked out between mem-
ory locations, thus allowing for a continuous stream of data to be read.
ERASE/WRITE (EWEN): To assure data integrity, the part automatically goes into the
Erase/Write Disable (EWDS) state when power is first applied. An Erase/Write Enable
(EWEN) instruction must be executed first before any programming instructions can be
carried out. Please note that once in the EWEN state, programming remains enabled
until an EWDS instruction is executed or V
CC power is removed from the part.
ERASE (ERASE): The Erase instruction programs all bits in the specified memory loca-
tion to the logical “1” state. The self-timed erase cycle starts once the ERASE instruction
and address are decoded. The DO pin outputs the Ready/Busy status of the part if CS is
brought high after being kept low for a minimum of 250 ns (t
CS). A logic “1” at pin DO
indicates that the selected memory location has been erased, and the part is ready for
another instruction.
Table 5. Instruction Set for the AT93C56A and AT93C66A
Instruction
SB
Op
Code
Address
Data
Comments
x 8
x 16
x 8
x 16
READ
1
10
A8 – A0
A7 – A0
Reads data stored in memory, at
specified address.
EWEN
1
00
11XXXXXXX
11XXXXXX
Write enable must precede all
programming modes.
ERASE
1
11
A8 – A0
A7 – A0
Erases memory location An – A0.
WRITE
1
01
A8 – A0
A7 – A0
D7 – D0
D15 – D0
Writes memory location An – A0.
ERAL
1
00
10XXXXXXX
10XXXXXX
Erases all memory locations. Valid
only at VCC = 4.5V to 5.5V.
WRAL
1
00
01XXXXXXX
01XXXXXX
D
7 – D0
D
15 – D0
Writes all memory locations. Valid
only at V
CC = 5.0V ±10% and Disable
Register cleared.
EWDS
1
00
00XXXXXXX
00XXXXXX
Disables all programming instructions.
相关PDF资料 |
PDF描述 |
|---|---|
| AT93C56A | 3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16) |
| ATE2DGPC1 | TOGGLE SWITCH, DPDT, LATCHED, THROUGH HOLE-STRAIGHT |
| ATFC-0201-8N2-J-T | 1 ELEMENT, 0.0082 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| ATFC-0201-5N6-G-T | 1 ELEMENT, 0.0056 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| ATFC-0201-10N-J-T | 1 ELEMENT, 0.01 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT93C56A-10PI-2.7 | 功能描述:IC EEPROM 2KBIT 2MHZ 8DIP RoHS:否 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并联 电源电压:2.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| AT93C56A-10PU-1.8 | 功能描述:电可擦除可编程只读存储器 E2 2K 3-WIRE 1M CYC - 10MS 1.8V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT93C56A-10PU-2.7 | 功能描述:电可擦除可编程只读存储器 E2 2K 3-WIRE 1M CYCLES - 10MS 2.7V RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| AT93C56A-10SA-3.3C | 制造商:Atmel Corporation 功能描述:ELECTRONIC COMPONENT |
| AT93C56A-10SE-2.7 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:3-wire Serial EEPROMs 2K (256 x 8 or 128 x 16) |
发布紧急采购，3分钟左右您将得到回复。