参数资料
| 型号： | ATAVRBC100 |
| 厂商： | Atmel |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | REF DESIGN KIT BATTERY CHARGER |
| 产品培训模块： | MCU Product Line Introduction tinyAVR Introduction |
| 标准包装： | 1 |
| 系列： | AVR® |
| 主要目的： | 电源管理，电池充电器 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | ATtiny261/461/861/25/45/85 |
| 主要属性： | 多化学，3 个电路，（2）1A/2.5A 时为 1.2 ~ 20V 输出，（1）5A 时为 1.2 ~ 38V |
| 次要属性： | 7.5 ~ 40V 输入，2 个继电器，支持可选 DB101 显示板 |
| 已供物品： | 板 |
| 产品目录页面： | 615 (CN2011-ZH PDF) |
| 相关产品： | ATTINY461-15MAZTR-ND - MCU AVR 4KB FLASH 15MHZ 20-QFN ATTINY861-15XZTR-ND - MCU AVR 8K FLASH 15MHZ 20-TSSOP ATTINY861-15SZTR-ND - MCU AVR 8K FLASH 15MHZ 20-SOIC ATTINY861-15MZTR-ND - MCU AVR 8K FLASH 15MHZ 32-QFN ATTINY85V-15STTR-ND - MCU AVR 8K FLASH 15MHZ 8-SOIC ATTINY85V-15MTTR-ND - MCU AVR 8K FLASH 15MHZ 20-QFN ATTINY85-15SZTR-ND - MCU AVR 8K FLASH 15MHZ 8-SOIC ATTINY85-15ST1TR-ND - MCU AVR 8K FLASH 15MHZ 8-SOIC ATTINY85-15STTR-ND - MCU AVR 8K FLASH 15MHZ 8-SOIC ATTINY85-15MZTR-ND - MCU AVR 8K FLASH 15MHZ 20-QFN 更多... |
AVR451
ATmega644 board controller it can be programmed regardless of the state of the SPI
lines. If SPI communication is used between a ATtiny and the ATmega644 a way to
ensure that programming is successful, is to erase the ATmega644 first, next
program the ATtiny and finally program the ATmega644.
During development the JTAG and DebugWire debugging interfaces are used, these
are not using the SPI lines to program the devices, and there are thus no special
procedures that should be followed to ensure successful programming.
In general the ATtinyx5 and the ATtinyx61 sockets should not be populated at the
same time, as the devices in these sockets are connected to the same traces on the
BC100. If devices are placed in both of these sockets it could potentially result in
drive contention.
4.6 Jumpers overview
A number of jumpers are available on the BC100, to be able to configure it for the
desired use. Please refer to Table 4-2 for a list of jumper and use, and refer to Figure
4-2 to identify the jumper’s location.
Table 4-2. Jumper and their use.
Designator
J302
J400/401
J402
J403
J404
J405
J406
Use and settings
Selects if the PB1 pin on ATtinyx5 is connected to the ISP/dW header or if
it is connected to the buck converters.
Use “PROG” position (left on Figure 4-2) when programming the
ATtinyx5.
Use “CHARGE” position when the ATtinyx5 should be connected to a
buck burst converter.
Select which buck converter the supply voltage is connected to use.
Two jumpers should be mounted in side by side at the label “BUCK-A”
(40V/5A), BUCK-B” (30V/2.5A) or BUCK-C” (20V/1A). “BUCK-A is the
Selects if the buck PWM control signal is connected or disconnected from
the BUCK-A (40V/5A). This jumper should be mounted in the disable
position while J403 or J404 is mounted in the enable position.
Selects if the buck PWM control signal is connected or disconnected from
the BUCK-B (30V/2.5A). This jumper should be mounted in the disable
position while J402 or J404 is mounted in the enable position.
Selects if the buck PWM control signal is connected or disconnected from
the BUCK-C (20V/1A). This jumper should be mounted in the disable
position while J402 or J403 is mounted in the enable position.
Selects the resistor divider network setting for the ADC input from the
V_BAT+ voltage (positive ADC input from shunt resistor).
The divider can be set to 1/2, 1/4, 1/8, 1/12, and 1/16 V_BAT+.
Note that the setting used should match the setting on J406.
Selects the resistor divider network setting for the ADC input from the
V_BAT- voltage (negative ADC input from shunt resistor).
The divider can be set to 1/2, 1/4, 1/8, 1/12, and 1/16 V_BAT-.
Note that the setting used should match the setting on J405.
9
8088A-AVR-09/07
相关PDF资料 |
PDF描述 |
|---|---|
| ATAVRDB101 | MODULE DISPLAY LCD/RGB BACKLIGHT |
| ATAVRMC100 | KIT EVALUATION FOR AT90PWM3 |
| ATAVRMC200 | KIT EVAL FOR AT90PWM3 ASYNC |
| ATAVRMC300 | BOARD EVAL LV MOTOR CONTROL PWR |
| ATAVRMC303 | BOARD EVAL MOTOR CTRL W/XMEGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATAVRBFLY | 功能描述:开发板和工具包 - AVR Evaluation tool w/preloaded firmware RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
| ATAVRBLE-IOT | 功能描述:SECURE AVR BLE IOT 制造商:microchip technology 系列:* 零件状态:在售 标准包装:1 |
| ATAVRCABLEKIT | 功能描述:电缆组件 AVR tools cable kit (USB+ribbon cables) RoHS:否 制造商:Molex 产品:Power Assemblies 类型:Cable Assembly 连接器端口 A:No Connector 连接器端口 A 管脚计数:4 连接器端口 B:No Connector 连接器端口 B 管脚计数: 型式:Male 线规 - 美国线规（AWG）:20, 28 长度:0.305 m 颜色:Black, Red |
| ATAVRDB101 | 功能描述:处理器配件 Display module RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于: |
| ATAVRDISPLAYX | 功能描述:开发板和工具包 - AVR XMEGA Display Evaluation Kit RoHS:否 制造商:Arduino 产品:Evaluation Boards 工具用于评估:ATMega32U4 核心:AVR 接口类型:I2C, UART, USB 工作电源电压:6 V to 20 V |
发布紧急采购，3分钟左右您将得到回复。