参数资料
| 型号： | ATF16V8BQL-15JC |
| 厂商： | Atmel |
| 文件页数： | 6/26页 |
| 文件大小： | 0K |
| 描述： | IC PLD 8CELL LOW PWR 15NS 20PLCC |
| 标准包装： | 48 |
| 系列： | 16V8 |
| 可编程类型： | EE PLD |
| 宏单元数： | 8 |
| 输入电压： | 5V |
| 速度： | 15ns |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-LCC（J 形引线） |
| 供应商设备封装： | 20-PLCC |
| 包装： | 管件 |
14
7707F–AVR–11/10
AT90USB82/162
There are basically two types of interrupts. The first type is triggered by an event that sets the
Interrupt Flag. For these interrupts, the Program Counter is vectored to the actual Interrupt Vec-
tor in order to execute the interrupt handling routine, and hardware clears the corresponding
Interrupt Flag. Interrupt Flags can also be cleared by writing a logic one to the flag bit position(s)
to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is
cleared, the Interrupt Flag will be set and remembered until the interrupt is enabled, or the flag is
cleared by software. Similarly, if one or more interrupt conditions occur while the Global Interrupt
Enable bit is cleared, the corresponding Interrupt Flag(s) will be set and remembered until the
Global Interrupt Enable bit is set, and will then be executed by order of priority.
The second type of interrupts will trigger as long as the interrupt condition is present. These
interrupts do not necessarily have Interrupt Flags. If the interrupt condition disappears before the
interrupt is enabled, the interrupt will not be triggered.
When the AVR exits from an interrupt, it will always return to the main program and execute one
more instruction before any pending interrupt is served.
Note that the Status Register is not automatically stored when entering an interrupt routine, nor
restored when returning from an interrupt routine. This must be handled by software.
When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled.
No interrupt will be executed after the CLI instruction, even if it occurs simultaneously with the
CLI instruction. The following example shows how this can be used to avoid interrupts during the
timed EEPROM write sequence..
When using the SEI instruction to enable interrupts, the instruction following SEI will be exe-
cuted before any pending interrupts, as shown in this example.
Assembly Code Example
in
r16, SREG
; store SREG value
cli
; disable interrupts during timed sequence
sbi
EECR, EEMPE
; start EEPROM write
sbi
EECR, EEPE
out
SREG, r16
; restore SREG value (I-bit)
C Code Example
char
cSREG;
cSREG = SREG; /* store SREG value */
/* disable interrupts during timed sequence */
__disable_interrupt();
EECR |= (1<<EEMPE); /* start EEPROM write */
EECR |= (1<<EEPE);
SREG = cSREG; /* restore SREG value (I-bit) */
相关PDF资料 |
PDF描述 |
|---|---|
| ATF16V8BQ-10JC | IC PLD 8CELL QTR PWR 10NS 20PLCC |
| ATF16V8B-10SC | IC PLD EE 10NS 20-SOIC |
| 3-1734592-0 | CONN FPC 30POS .5MM RT ANG SMD |
| AT22LV10L-25JI | IC PLD 25NS OTP 28PLCC |
| ABB80DHAS | CONN EDGECARD 160PS R/A .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATF16V8BQL-15JC-SL383 | 制造商:Atmel Corporation 功能描述:15NSQTR PWR W/ L PLCCCOM TEMP |
| ATF16V8BQL-15JI | 功能描述:EEPLD - 电子擦除可编程逻辑设备 250 GATE 15 NS WAFER - 15NS RoHS:否 制造商:Atmel 逻辑系列:ATF16V8BQL 最大工作频率:62 MHz 可编程输入/输出端数量:20 电源电流:20 mA 延迟时间:15 ns 每个宏指令的积项数:8 电源电压-最大:5.5 V 电源电压-最小:4.5 V 大电池数量:8 最小工作温度:- 40 C 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP-20 |
| ATF16V8BQL-15JU | 功能描述:EEPLD - 电子擦除可编程逻辑设备 15 ns 20 I/O Pins 8 macorcells 8 reg RoHS:否 制造商:Atmel 逻辑系列:ATF16V8BQL 最大工作频率:62 MHz 可编程输入/输出端数量:20 电源电流:20 mA 延迟时间:15 ns 每个宏指令的积项数:8 电源电压-最大:5.5 V 电源电压-最小:4.5 V 大电池数量:8 最小工作温度:- 40 C 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP-20 |
| ATF16V8BQL-15PC | 功能描述:EEPLD - 电子擦除可编程逻辑设备 250 GATE 15 NS WAFER - 15NS RoHS:否 制造商:Atmel 逻辑系列:ATF16V8BQL 最大工作频率:62 MHz 可编程输入/输出端数量:20 电源电流:20 mA 延迟时间:15 ns 每个宏指令的积项数:8 电源电压-最大:5.5 V 电源电压-最小:4.5 V 大电池数量:8 最小工作温度:- 40 C 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP-20 |
| ATF16V8BQL-15PC-RET | 制造商:Atmel Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。