参数资料
| 型号： | ATF16V8BQL-15XC |
| 厂商： | Atmel |
| 文件页数： | 17/26页 |
| 文件大小： | 0K |
| 描述： | IC PLD 15NS 20TSSOP |
| 标准包装： | 74 |
| 系列： | 16V8 |
| 可编程类型： | EE PLD |
| 宏单元数： | 8 |
| 输入电压： | 5V |
| 速度： | 15ns |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 管件 |
| 其它名称： | ATF16V8BQL15XC |
24
7707F–AVR–11/10
AT90USB82/162
be used. If a reset occurs while a write operation is in progress, the write operation will be com-
pleted provided that the power supply voltage is sufficient.
5.4
I/O Memory
The I/O space definition of the AT90USB82/162 is shown in “Register Summary” on page 288.
All AT90USB82/162 I/Os and peripherals are placed in the I/O space. All I/O locations may be
accessed by the LD/LDS/LDD and ST/STS/STD instructions, transferring data between the 32
general purpose working registers and the I/O space. I/O Registers within the address range
0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the
value of single bits can be checked by using the SBIS and SBIC instructions. Refer to the
instruction set section for more details. When using the I/O specific commands IN and OUT, the
I/O addresses 0x00 - 0x3F must be used. When addressing I/O Registers as data space using
LD and ST instructions, 0x20 must be added to these addresses. The AT90USB82/162 is a
complex microcontroller with more peripheral units than can be supported within the 64 location
reserved in Opcode for the IN and OUT instructions. For the Extended I/O space from 0x60 -
0x1FF in SRAM, only the ST/STS/STD and LD/LDS/LDD instructions can be used.
For compatibility with future devices, reserved bits should be written to zero if accessed.
Reserved I/O memory addresses should never be written.
Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most
other AVRs, the CBI and SBI instructions will only operate on the specified bit, and can therefore
be used on registers containing such Status Flags. The CBI and SBI instructions work with reg-
isters 0x00 to 0x1F only.
The I/O and peripherals control registers are explained in later sections.
5.4.1
General Purpose I/O Registers
The AT90USB82/162 contains three General Purpose I/O Registers. These registers can be
used for storing any information, and they are particularly useful for storing global variables and
Status Flags. General Purpose I/O Registers within the address range 0x00 - 0x1F are directly
bit-accessible using the SBI, CBI, SBIS, and SBIC instructions.
5.4.2
General Purpose I/O Register 2 – GPIOR2
5.4.3
General Purpose I/O Register 1 – GPIOR1
5.4.4
General Purpose I/O Register 0 – GPIOR0
Bit
765432
1
0
MSB
LSB
GPIOR2
Read/Write
R/W
Initial Value
000000
0
Bit
7654
3
2
1
0
MSB
LSB
GPIOR1
Read/Write
R/WR/W
Initial Value
0000
0
Bit
765432
1
0
MSB
LSB
GPIOR0
Read/Write
R/W
Initial Value
000000
0
相关PDF资料 |
PDF描述 |
|---|---|
| ATF16V8C-7XU | IC PLD 7NS 20TSSOP |
| ATF16V8CZ-15XC | IC PLD 15NS 20TSSOP |
| ATF20V8BQL-15PU | IC PLD 15NS 24DIP |
| ATF22LV10C-15XC | IC PLD 15NS 24TSSOP |
| ATF22LV10CZ-25XC | IC PLD 25NS 24TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATF16V8BQL-15XI | 功能描述:EEPLD - 电子擦除可编程逻辑设备 250 GATE 15 NS WAFER - 15NS RoHS:否 制造商:Atmel 逻辑系列:ATF16V8BQL 最大工作频率:62 MHz 可编程输入/输出端数量:20 电源电流:20 mA 延迟时间:15 ns 每个宏指令的积项数:8 电源电压-最大:5.5 V 电源电压-最小:4.5 V 大电池数量:8 最小工作温度:- 40 C 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP-20 |
| ATF16V8BQL-15XU | 功能描述:EEPLD - 电子擦除可编程逻辑设备 15 ns 20 I/O Pins 8 macorcells 8 reg RoHS:否 制造商:Atmel 逻辑系列:ATF16V8BQL 最大工作频率:62 MHz 可编程输入/输出端数量:20 电源电流:20 mA 延迟时间:15 ns 每个宏指令的积项数:8 电源电压-最大:5.5 V 电源电压-最小:4.5 V 大电池数量:8 最小工作温度:- 40 C 最大工作温度:+ 85 C 安装风格:Through Hole 封装 / 箱体:PDIP-20 |
| ATF16V8BQL-25GM | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electrically-Erasable PLD |
| ATF16V8BQL-25GM/883 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Electrically-Erasable PLD |
| ATF16V8BQL25JC | 制造商:Atmel Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。