参数资料
型号: ATMEGA1284-AUR
厂商: Atmel
文件页数: 133/160页
文件大小: 0K
描述: IC MCU AVR 128K FLASH 44TQFP
产品培训模块: megaAVR Introduction
标准包装: 1
系列: AVR® ATmega
核心处理器: AVR
芯体尺寸: 8-位
速度: 20MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 32
程序存储器容量: 128KB(64K x 16)
程序存储器类型: 闪存
EEPROM 大小: 4K x 8
RAM 容量: 16K x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 5.5 V
数据转换器: A/D 8x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 44-TQFP
包装: 剪切带 (CT)
74
8272E–AVR–04/2013
ATmega164A/PA/324A/PA/644A/PA/1284/P
If PORTxn is written logic one when the pin is configured as an output pin, the port pin is driven
high (one). If PORTxn is written logic zero when the pin is configured as an output pin, the port
pin is driven low (zero).
14.2.2
Toggling the pin
Writing a logic one to PINxn toggles the value of PORTxn, independent on the value of DDRxn.
Note that the SBI instruction can be used to toggle one single bit in a port.
14.2.3
Switching between input and output
When switching between tri-state ({DDxn, PORTxn} = 0b00) and output high ({DDxn, PORTxn}
= 0b11), an intermediate state with either pull-up enabled {DDxn, PORTxn} = 0b01) or output
low ({DDxn, PORTxn} = 0b10) must occur. Normally, the pull-up enabled state is fully accept-
able, as a high-impedant environment will not notice the difference between a strong high driver
and a pull-up. If this is not the case, the PUD bit in the MCUCR Register can be set to disable all
pull-ups in all ports.
Switching between input with pull-up and output low generates the same problem. The user
must use either the tri-state ({DDxn, PORTxn} = 0b00) or the output high state ({DDxn, PORTxn}
= 0b11) as an intermediate step.
Table 14-1 summarizes the control signals for the pin value.
14.2.4
Reading the Pin Value
Independent of the setting of Data Direction bit DDxn, the port pin can be read through the
PINxn Register bit. As shown in Figure 14-2, the PINxn Register bit and the preceding latch con-
stitute a synchronizer. This is needed to avoid metastability if the physical pin changes value
near the edge of the internal clock, but it also introduces a delay. Figure 14-3 shows a timing dia-
gram of the synchronization when reading an externally applied pin value. The maximum and
minimum propagation delays are denoted t
pd,max and tpd,min respectively.
Table 14-1.
Port pin configurations.
DDxn
PORTxn
PUD
(in MCUCR)
I/O
Pull-up
Comment
0
X
Input
No
Tri-state (Hi-Z)
0
1
0
Input
Yes
Pxn will source current if ext. pulled low.
0
1
Input
No
Tri-state (Hi-Z)
1
0
X
Output
No
Output Low (Sink)
1
X
Output
No
Output High (Source)
相关PDF资料
PDF描述
MS27473E18A32P CONN PLUG 32POS STRAIGHT W/PINS
MS27508E16F35S CONN RCPT 55POS BOX MNT W/SCKT
D38999/20FD15PB CONN RCPT 15POS WALL MNT W/PINS
D38999/26FC98PN CONN PLUG 10POS STRAIGHT W/PINS
VE-BTP-IW-F1 CONVERTER MOD DC/DC 13.8V 100W
相关代理商/技术参数
参数描述
ATMEGA1284-MU 功能描述:8位微控制器 -MCU AVR 128KB FLSH 4KB EE16KB SRAM-20 MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA1284-MUR 功能描述:8位微控制器 -MCU AVR 128KB FLSH 4KB EE16KB SRAM-20 MHz RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA1284P 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
ATMEGA1284P_09 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash
ATMEGA1284P_1 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 128K Bytes In-System Programmable Flash