参数资料
型号: ATMEGA168V-10MI
厂商: Atmel
文件页数: 17/36页
文件大小: 0K
描述: IC AVR MCU 16K 10MHZ 32-QFN
产品培训模块: megaAVR Introduction
标准包装: 490
系列: AVR® ATmega
核心处理器: AVR
芯体尺寸: 8-位
速度: 10MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 23
程序存储器容量: 16KB(8K x 16)
程序存储器类型: 闪存
EEPROM 大小: 512 x 8
RAM 容量: 1K x 8
电压 - 电源 (Vcc/Vdd): 1.8 V ~ 5.5 V
数据转换器: A/D 8x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 32-VFQFN 裸露焊盘
包装: 托盘
24
2545TS–AVR–05/11
ATmega48/88/168
11.1.4
Rev A
Part may hang in reset
Wrong values read after erase only operation
Watchdog timer interrupt disabled
Start-up time with crystal oscillator is higher than expected
High power consumption in power-down with external clock
Asynchronous oscillator does not stop in power-down
Interrupts may be lost when writing the timer registers in the asynchronous timer
1.
Part may hang in reset
Some parts may get stuck in a reset state when a reset signal is applied when the internal
reset state-machine is in a specific state. The internal reset state-machine is in this state for
approximately 10ns immediately before the part wakes up after a reset, and in a 10ns win-
dow when altering the system clock prescaler. The problem is most often seen during In-
System Programming of the device. There are theoretical possibilities of this happening also
in run-mode. The following three cases can trigger the device to get stuck in a reset-state:
- Two succeeding resets are applied where the second reset occurs in the 10ns window
before the device is out of the reset-state caused by the first reset.
- A reset is applied in a 10ns window while the system clock prescaler value is updated by
software.
- Leaving SPI-programming mode generates an internal reset signal that can trigger this
case.
The two first cases can occur during normal operating mode, while the last case occurs only
during programming of the device.
Problem fix/workaround
The first case can be avoided during run-mode by ensuring that only one reset source is
active. If an external reset push button is used, the reset start-up time should be selected
such that the reset line is fully debounced during the start-up time.
The second case can be avoided by not using the system clock prescaler.
The third case occurs during In-System programming only. It is most frequently seen when
using the internal RC at maximum frequency.
If the device gets stuck in the reset-state, turn power off, then on again to get the device out
of this state.
2.
Wrong values read after erase only operation
At supply voltages below 2.7V, an EEPROM location that is erased by the Erase Only oper-
ation may read as programmed (0x00).
Problem fix/workaround
If it is necessary to read an EEPROM location after Erase Only, use an Atomic Write opera-
tion with 0xFF as data in order to erase a location. In any case, the Write Only operation can
be used as intended. Thus no special considerations are needed as long as the erased loca-
tion is not read before it is programmed.
相关PDF资料
PDF描述
PIC16F873A-I/SO IC MCU FLASH 4KX14 EE 28SOIC
PIC16F873A-I/SP IC MCU FLASH 4KX14 EE 28DIP
PIC32MX320F032H-40V/PT IC MCU 32BIT 32KB FLASH 64TQFP
ATMEGA3290-16AI IC AVR MCU 32K 16MHZ 100TQFP
5172069-3 DRAWER CONN 12P FEMALE
相关代理商/技术参数
参数描述
ATMEGA168V-10MJ 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 8K Bytes In-System Programmable Flash
ATMEGA168V-10MQ 功能描述:8位微控制器 -MCU AVR 16KB, 512B EE 10MHz 1KB SRAM, 1.8V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA168V-10MQR 功能描述:8位微控制器 -MCU AVR,16KB FLASH,20MHZ EXT.TEMP RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATMEGA168V-10MQR QS610 制造商:Atmel Corporation 功能描述:
ATmega168V-10MU 功能描述:8位微控制器 -MCU 16kB Flash 0.5kB EEPROM 23 I/O Pins RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT