- 您现在的位置：买卖IC网 > PDF目录21916 > ATS645LSH-I2TN (Allegro Microsystems Inc)IC SENSOR GEAR TOOTH 4-SIP PDF资料下载
参数资料
| 型号： | ATS645LSH-I2TN |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 5/14页 |
| 文件大小： | 381K |
| 描述： | IC SENSOR GEAR TOOTH 4-SIP |
| 标准包装： | 800 |
| 传感范围： | 120mV 跳闸，120mV 释放 |
| 类型： | 专用型 |
| 电源电压： | 4 V ~ 24 V |
| 电流 - 电源： | 8.4mA |
| 输出类型： | 数字，开路集电极 |
| 特点： | 轮齿类型 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 4-SIP |
| 供应商设备封装： | 4-SIP |
| 包装： | 带卷 (TR) |
True Zero Speed Miniature Differential Peak-
Detecting Gear Tooth Sensor IC
ATS645LSH
4
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
OPERATING CHARACTERISTICS (continued) using reference target 60-0, T
A
and V
CC
within speci cation, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min. Typ.
1
Max. Units
SWITCHPOINT CHARACTERISTICS
Rotation Speed
S
ROT
Reference Target 60-0
0 8,000 rpm
Analog Signal Bandwidth
BW Equivalent to f 3dB
20 40 kHz
Operate Point
B
OP
Transitioning from I
CC(High)
to I
CC(Low)
; positive peak
referenced; AG < AG
MAX
120 mV
Release Point
B
RP
Transitioning from I
CC(Low)
to I
CC(High)
; negative peak
referenced; AG < AG
MAX
120 mV
CALIBRATION
Initial Calibration
C
I
Quantity of rising output (current) edges required for
accurate edge detection
3 Edge
DAC CHARACTERISTICS
Allowable User-Induced Differential
Offset
Output switching only; may not meet datasheet speci-
cations
60 60 G
FUNCTIONAL CHARACTERISTICS
5
Operational Air Gap Range
6
AG DC within speci cation
0.5 2.75 mm
Maximum Operational Air Gap
Range
AG
OP(max)
Output switching (no missed edges); DC not
guaranteed
3 mm
Duty Cycle Variation
7
DC
Wobble < 0.5mm; Typical value at AG = 1.5 mm, for
max., min., AG within speci cation
43 53 63 %
Operating Magnetic Flux Density
Differential
8
B
AG(p-p)
Operating within speci cation
30 1000 G
Minimum Operating Signal
Sig
OP(min)
Output switching (no missed edges); DC not
guaranteed
20 G
1
Typical values are at T
A
= 25癈 and V
CC
= 12 V. Performance may vary for individual units, within the speci ed maximum and minimum limits.
2
Maximum voltage must be adjusted for power dissipation and junction temperature; see Power Derating section.
3
Power-On Time includes the time required to complete the internal automatic offset adjust. The DACs are then ready for peak acquisition.
4
dI is the difference between 10% of I
CC(Low)
and 90% of I
CC(High)
, and dt is time period between those two points.
Note: di/dt is dependent upon the value of the bypass capacitor, if one is used.
5
Functional characteristics valid only if magnetic offset is within the speci ed range for Allowable User Induced Differential Offset.
6
AG is dependent on the available magnetic eld. The available eld is dependent on target geometry and material, and should be independently
characterized. The eld available from the reference target is given in the reference target parameter section of the datasheet.
7
Duty cycle speci cation may not be met if the magnetic signal during the calibration period is not representative of the installation air gap.
8
In order to remain in speci cation, the magnetic gradient must induce an operating signal greater than the minimum value speci ed. This includes the
effect of target wobble.
相关PDF资料 |
PDF描述 |
|---|---|
| ATS643LSH-I2 | IC SENSOR GEAR TOOTH 4-SIP |
| ATS643LSH-I1TN | IC SENSOR GEAR TOOTH 4-SIP |
| US-4016 | PROTO-BOARD 16PIN THRU-HOLE SIP |
| ATS636LSETN | IC SENSOR GEAR TOOTH 4-SIP |
| 6410 | PROTO-BRD 10PIN DISCRETE SMD SIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATS645LSHTN-I1 | 功能描述:IC SENSOR GEAR TOOTH 4-SIP RoHS:否 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| ATS645LSHTN-I1-T | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:True Zero Speed Miniature Gear Tooth Sensor |
| ATS645LSHTN-I2-T | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:True Zero Speed Miniature Gear Tooth Sensor |
| ATS651LSH | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Two-Wire Self-Calibrating Differential Speed and Direction Sensor with Vibration Immunity |
| ATS651LSH_05 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Two-Wire Self-Calibrating Differential Speed and Direction Sensor with Vibration Immunity |
发布紧急采购，3分钟左右您将得到回复。