- 您现在的位置：买卖IC网 > PDF目录21916 > ATS673LSETN-LT (Allegro Microsystems Inc)IC SENSOR GEAR TOOTH 4LEAD PDF资料下载
参数资料
| 型号： | ATS673LSETN-LT |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 5/20页 |
| 文件大小： | 968K |
| 描述： | IC SENSOR GEAR TOOTH 4LEAD |
| 标准包装： | 450 |
| 传感范围： | 40% 空气间隙跳闸，50% 空气间隙释放 |
| 类型： | 专用型 |
| 电源电压： | 3.3 V ~ 26.5 V |
| 电流 - 电源： | 11mA |
| 电流 - 输出（最大）： | 20mA |
| 输出类型： | 数字，开路集电极 |
| 特点： | 轮齿类型 |
| 工作温度： | -40°C ~ 150°C |
| 封装/外壳： | 4-SIP |
| 供应商设备封装： | 4-SIP |
| 包装： | 带卷 (TR) |
Self-Calibrating TPOS Gear Tooth Sensor ICs
Optimized for Automotive Cam Sensing Applications
ATS673 and
ATS674
4
Allegro MicroSystems, LLC
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
SWITCHPOINT CHARACTERISTICS
Tooth Speed
S Tooth frequency, target generating sinusoidal signal
0
8
kHz
Bandwidth
BW Corresponds to output switching frequency 3 dB
40
kHz
Operate
B
OP
ATS673
% of peak-to-peak, referenced to tooth signal,
AG < AG
(Max)
40
%
ATS674
30
%
Release
B
RP
ATS673
% of peak-to-peak, referenced to tooth signal,
AG < AG
(Max)
50
%
ATS674
40
%
CALIBRATION CHARACTERISTICS
4
Initial Calibration
Cal
IC
Quantity of rising edges required to complete edge detec-
tion calibration
3 edges
AGC Disable
Cal
AGC
Quantity of rising edges required to complete Automatic
Gain Control calibration
3 edges
Calibration Update
Cal
UPD
Quantity of rising edges required to update edge detection
calibration while running after initial calibration
Contin-
uous
edges
PERFORMANCE CHARACTERISTICS
3
TPOS Air Gap Range
5
AG
TPOS
TPOS functionality guaranteed
0.5
2.5 mm
Operational Air Gap Range
AG TPOS guaranteed, output switching, running mode
0.5
2.5 mm
Extended Minimum Air Gap
6
AG
EXTMIN
Output switching, running mode; valleys may be detected
as teeth in this range
0.5 mm
Extended Maximum Air Gap
7
AG
EXTMAX
Output switching, running mode; teeth may be detected as
valleys in this range
2.5
5
mm
Relative Timing Accuracy
4,8
Err
ICREL
ATS673
During initial calibration; rising or falling edges,
gear speed = 1000 rpm, target eccentricity
< 0.1 mm
3
6
deg
ATS674
3
6
deg
Err
RELR
ATS673
Rising edges; after initial calibration, gear speed
= 1000 rpm, target eccentricity < 0.1 mm
0.5 0.8 deg
ATS674
0.4 0.8 deg
Err
RELF
ATS673
Falling edges; after initial calibration, gear speed
= 1000 rpm, target eccentricity < 0.1 mm
0.8 1.2 deg
ATS674
0.6 1.2 deg
Phase Delay
9
DErr
SREL
After initial calibration, AG = 1.5 mm, T
A
= 25癈
1.6 x 10
4
deg/rpm
1
Typical values are taken at V
CC
= 12 V and T
A
= 25癈.
2
I
ZSupply(Max)
is equivalent to I
CCON(Max)
+ 3 mA.
3
Using reference target 8X.
4
The term edge refers to a mechanical edge, such as the side of a gear tooth, passing under the device. Rising edge: from valley to approaching tooth.
Falling edge: from tooth to approaching valley.
5
The TPOS Air Gap Range is the range of installation air gaps within which the TPOS (True Power-On State) function is guaranteed to correctly detect
a tooth when powered-on over a tooth and correctly detecting a valley when powered-on over a valley, using reference target 8X or equivalent, as
specified in the Target/Gear Parameters for Correct TPOS Operation section in this document.
6
The Extended Minimum Air Gap is a range of installation air gaps, smaller than AG
(Min)
, within which the the device will accurately detect target fea-
tures but TPOS is NOT guaranteed to be fully accurate, possibly evaluating the initial valley as a tooth.
7
The Extended Maximum Air Gap is an extended range of installation air gaps, greater than AG
(Max)
, within which the the device will accurately detect
target features but TPOS is not guaranteed to be fully accurate, possibly evaluating the intiial tooth as a valley.
8
Relative Timing Accuracy is the change in edge position before the resulting change in device output; for a single device, over the full Operational Air
Gap Range, AG, and Operating Ambient Temperature, T
A
, range.
9
Phase Delay is the change in edge position at detection, through the full operational Tooth Speed, S, range for a single device, and at a single ambi-
ent temperature, T
A
, and installation air gap, AG.
OPERATING CHARACTERISTICS, continued Valid at T
A
= 40癈 to 150癈, T
J
d T
J(max)
, over full range of AG, unless otherwise noted
Characteristic
Symbol
Test Conditions
Min. Typ.
1
Max. Units
相关PDF资料 |
PDF描述 |
|---|---|
| US-5016 | PROTO-BOARD 16PIN THRU-HOLE SIP |
| ASEM1-29.4912MHZ-LC-T | OSC MEMS 29.4912 MHZ 3.3V SMD |
| 4768-K-36 | DBL BANA/MICROGRAB RG174/U 36" |
| ZXMN2A01FTA | MOSFET N-CH 20V 1.9A SOT23-3 |
| 4768-K-24 | DBL BANA/MICROGRAB RG174/U 24" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATS673LSETN-LT-T | 功能描述:IC SENSOR TPOS GEAR TOOTH 4-SIP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| ATS674 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| ATS674LSETN-HT | 制造商:Allegro MicroSystems LLC 功能描述: |
| ATS674LSETN-HT-T | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Self-Calibrating TPOS Gear Tooth Sensor Optimized for Automotive Cam Sensing Applications |
| ATS674LSETN-LT | 功能描述:IC SENSOR GEAR TOOTH 4LEAD RoHS:否 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
发布紧急采购，3分钟左右您将得到回复。